BAQ alphaDUR mini Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 50

BAQ alphaDUR mini Скачать руководство пользователя страница 23

CONVERSION OF HARDNESS VALUES

7 Conversion of hardness values

The

alphaDUR mini

can convert hardness values to another hardness scale.

The tables DIN EN ISO 18265 - Feb.2014 and ASTM E140 - 12b (2019) are

used for the conversion. These tables partly contain values, which are outside

of the definition area of the standardized hardness testing method, but may be

used as approximate values. In the

alphaDUR mini

, these approximate values

are considered in the conversion and shown in red on the display.

When applying revaluations, it should be noted that there is no universal

conversion relation. That is why the conversions should only be used within a

material group. The impact of different indenters and test loads should always

be considered. The information given in the standards on the applicability,

inaccuracy and the difficulties when converting hardness values should be

taken into account. Before using the conversion it should be checked if all

requirements for the conversion are met.

The

alphaDUR mini

determines the Vickers hardness. In contrast to the

classical method according to DIN EN ISO 6507-1, the measurement is done

while the test load is applied. Still the results of the UCI-Vickers and the

Standard-Vickers are comparable to the classical method, as long as the elastic

part of the deformation is negligible compared to the plastic part. This applies to

metals and e.g. ceramics.

To change the hardness scale, select the menu item

Measuring parameter /

Edit / Hardness scale

(see chapter 6.2.1) or press the SCALE key in the

measuring window. The SCALE KEY is deactivated if the measured data

storage is activated.

The ranges of validity for hardness conversion are shown in chapter 15

Appendix 1: Hardness conversion validity ranges

23

«
...
21
22
23
24
25
...
»

Содержание alphaDUR mini



















































Отзывы:

Нет отзывов