D10
Expert
™
Dual Discrete Outputs
8
P/N 64154 rev. F
Banner Engineering Corp.
•
Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Figure 9. Single-Point Dark SET (Light
Operate shown)
Sensor positions
window thresholds
≈10%
from the
presented condition
Sensor positions
threshold between
taught conditions
Threshold position
adjusted by
Manual Adjust
Threshold position
adjusted by
Manual Adjust
Sensor positions
threshold between
taught conditions
Sensor positions
threshold slightly below
the presented condition
Sensor positions
threshold slightly above
the presented condition
Darkest
(no signal)
Darkest
(no signal)
Darkest
(no signal)
Most Light
(saturated
signal)
Most Light
(saturated
signal)
Darkest
(no signal)
Most Light
(saturated
signal)
Most Light
(saturated
signal)
Condition
Presented
Sensing window size
adjusted by
Manual Adjust
Output OFF
Output OFF
Output OFF
Output ON
Output ON
Darkest Taught
Condition
Lightest Taught
Condition
Position
adjusted by
Manual Adjust
Output OFF
Output ON
Condition
Presented
Output OFF
Output ON
Condition
Presented
Darkest
(no signal)
Most Light
(saturated
signal)
Output OFF
Output ON
2nd Taught
Condition
1st Taught
Condition
Position
adjusted by
Manual Adjust
Push Button
0.04 seconds ≤ “Click” ≤ 0.8 seconds
Remote Line
0.04 seconds ≤ T ≤ 0.8 seconds
Result
Access
SET
Mode
• Press and hold
Static push button
> 2 seconds
• Single-pulse
remote line
• Display flashes “
1st
”
• Arrow icon turns red
• Display flashes “
2nd
”
• Arrow icon turns red
SET
Output
OFF
Condition
• Present Output
OFF condition
• Five-click
Static push
button
• Present Output
OFF condition
• Five-pulse remote line
Threshold Condition Accepted
• Display flashes “
sngl
” then “
dr
” twice
• Sensor returns to RUN mode with new settings
• Arrow icon turns green
Threshold Condition Unacceptable
• Display flashes “
fail
” and returns to “
1st
”
• Arrow icon remains red
• After 60 seconds, sensor returns to RUN mode
(Arrow icon turns green) without changing
settings
T
T T T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T T T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Push Button
Remote
dynamic
static
dynamic
static
dynamic
static
dynamic
static
dynamic
static
dynamic
static
Mode
Threshold Offset
(counts above
taught signal value)
Super High-Speed
30
High-Speed
22
High-Power
9
Super High-Power
6
Figure 10. Dark SET Threshold Offset
Single-Point Dark SET
• Sets a threshold slightly above the taught condition (see figure 9).
• Any condition lighter than the threshold condition causes the output to change state.
• Threshold position is adjustable using “+” and “-” buttons (see Manual Adjust, page 9)
• Recommended for applications where only one condition is known, for example a stable dark
background with varying lighter targets.
A single sensing condition is presented, and the sensor positions a threshold slightly above
the taught condition. When a condition lighter than the threshold is sensed, the output either
turns ON or OFF, depending on the Light/Dark Operate setting (see Sensor Setup, page 10.)
Dark SET and Light/Dark Operate Selection
Dark SET teaches the Output OFF condition and forces the sensor into Light Operate (LO)
mode. The sensor can be reconfigured to Dark Operate (DO) mode after the condition has
been taught (see Sensor Setup, page 10).
