Technical data • Complete system
42
Panel PC 800 User's Manual V1.30
2.6.2 Monitor/Panel interface
Monitor/Panel interface - SDL (Smart Display Link) / DVI
The following is an overview of the video signals available on the monitor/panel output.
For details, see the technical data for the CPU board being used.
CPU board
Video signals with all system unit variants
5PC800.B945-00 / -10
SDL, DVI, RGB
5PC800.B945-01 / -11
SDL, DVI, RGB
5PC800.B945-02 / -12
SDL, DVI, RGB
5PC800.B945-03 / -13
SDL, DVI, RGB
5PC800.B945-04 / -14
SDL, DVI, RGB
5PC800.B945-05
SDL, DVI, RGB
Table 12: Monitor/Panel interface - SDL, DVI, RGB
Information:
Hot-plugging of display devices on the monitor/panel interface is not supported. The male monitor/pan-
el connector is specified for 100 connection cycles.
Information:
Bei der RGB-Schnittstelle handelt es sich um ein analoges Signal, die mögliche Leitungslänge ist von
der Auflösung sowie den herrschenden Umwelteinflüssen abhängig. This interface is therefore only
recommended for service purposes.
2.6.2.1 Pinout
Pin Assignment
Description
Pin Assignment
Description
1 TMDS data 2-
DVI lane 2 (negative)
16 HPD
Hot plug detect
2 TMDS data 2+
DVI lane 2 (positive)
17 TMDS data 0-
DVI lane 0 (negative)
3 TMDS data 2/4
SHIELD
Shield for data pair 2 and 4
18 TMDS data 0+
DVI lane 0 (positive)
4 SDL-
SDL lane (negative)
19 TMDS Data 0/
XUSB1 SHIELD
Shield for data pair 0 and
USB1
5 SDL+
SDL lane (positive)
20 XUSB1-
USB lane 1 (negative)
6 DDC clock
DDC-based control signal
(clock)
21 XUSB1+
USB lane 1 (positive)
7 DDC data
DDC-based control signal
(data)
22 TMDS clock
shield
Shield for clock pair
8 N.C.
Not connected
23 TMDS clock+
DVI clock (positive)
9 TMDS data 1-
DVI lane 1 (negative)
24 TMDS clock -
DVI clock (negative)
10 TMDS DATA 1+ DVI lane 1 (negative) HDMI
clock (positive)
C1 ANALOG RED Analog red
11 TMDS DATA 1/
XUSB0 SHIELD
Shield for data pair 1 and
USB0
C2 ANALOG
GREEN
Analog green
12 XUSB0-
USB lane 0 (negative)
C3 ANALOG BLUE Analog blue
13 XUSB0+
USB lane 0 (positive)
C4 ANALOG
HORZ SYNC
Analog horizontal synchro-
nization
14 +5 V power
1)
+5 V power supply
C5 ANALOG GND Analog ground (return for R,
G and B signals)
15
Ground (return
for +5 V, HSync
and VSync)
Ground
24-pin female DVI connector
6 7 8
5
1 2 3 4
14 15 16
13
9 10 11 12
22 23 24
21
17 18 19 20
c1
c4
c2
c3
c5
Table 13: DVI interface - Pinout
1)
Protected internally by a multifuse.
2.6.2.2 USB communication in SDL and DVI mode
Information:
In SDL mode, the USB transfer rate is limited to USB 1.1.
In DVI mode, the maximum USB transfer rate is determined by the USB interface and USB hub on the
display device.