B&D Smart Pro SDO-9V3 страница 29 Скачать руководство пользователя

Страница: 29 / 29

b&d doors office locations

Head Office

6-8 Fiveways Blvd, Keysborough 3073

Phone (03) 9791 2000

New South Wales

34 Marigold St, Revesby 2212

Phone (02) 9722 5555

Queensland

17 Oasis Court, Clontarf 4019

Phone (07) 3883 0200

Victoria

147-153 Canterbury Rd, Kilsyth 3137

Phone (03) 9237 7766

South Australia

23 Frederick Rd, Royal Park 5014

Phone (08) 8440 4747

Western Australia

96 Mulgul Rd, Malaga 6090

Phone (08) 9247 8777

International/Export

34 Marigold St, Revesby 2212

Phone +61 (0)2 9722 5555

www.bnd.com.au

Prefixed trademarks are the property of B&D Australia Pty Ltd. B&D Doors & Openers
is a division of B&D Australia Pty Ltd. ABN 25 010 473 971. © 2018 B&D Australia Pty Ltd.

your representative is

Smart Pro, Smart & Secure

installation instructions

G - Setting up Tilt Door

Prior to limit set up, the opener can be set to J-Type Tilt

Profile. This process allows the opener to pre-set to J-Type

settings where the limit is not greater than 1500mm.

In JTYPE Mode the drive speed is reduced

and cannot be adjusted.

tip

S T E P O N E

S E T T I N G U P T I L T D O O R

S T E P T W O

To activate JTYPE Mode

Press together and opener

will beep TWICE

To return to Standard Mode

Press together and opener

will beep ONCE

S T E P T H R E E

Switch power on

BLUE LED will flash

& gear LED lit

S T E P F O U R

To move the door to the

halfway point.

Proceed to Setting

Close Limit position.

If installing on a door with a bad wave action,

lengthening the arm will assist in reducing this

effect.

tip

Содержание Smart Pro SDO-9V3






























Результаты поиска

Содержание Smart Pro SDO-9V3

Отзывы:

Похожие инструкции для Smart Pro SDO-9V3

Бренды по названию

Популярные бренды

B&D Smart Pro SDO-9V3, Руководство по установке

Результаты поиска

Содержание Smart Pro SDO-9V3

Отзывы:

Похожие инструкции для Smart Pro SDO-9V3

Бренды по названию

Популярные бренды