Bally IM-268S-11 Скачать руководство пользователя страница 1

Страница: 1 / 10

REV: 5/2013

IM-268S-11 2013 © Bally Refrigerated Boxes, Inc.

SERVICE MANUAL

WALK-IN COOLERS AND FREEZER

IM-268S-11

Routine maintenance

Safety Walk Strips

Gaskets

Replacing magnetic gasket on hinged Walk-In doors

Replacing wiper gasket at bottom of hinged Walk-In door

Hinged Walk-In Doors

Replacing the D-1000 touch latch on Walk-In doors

Replacing D-1250 spring loaded hinges on Walk-In door panels

Shimming Walk-In door hinges

Anti-Condensate Heaters

Replacing anti-condensate heater element around door frame of hinged Walk-In doors

Reach-In Doors

Replacing magnetic gasket on hinged Reach-In doors

Adjusting self-closing hinges on Reach-In doors

Replacing hinges on Reach-In door panels

Replacing anti-condensate heater element around frame of hinged Reach-In doors

Pressure Relief Port

Replacing klixon on Pressure Relief Port

Replacing anti-condensate heaters on Pressure Relief Ports

Replacing magnetic gasket on Pressure Relief Ports

Door Closer

Replacing Door Closer

Содержание IM-268S-11











Результаты поиска

Содержание IM-268S-11

Отзывы:

Похожие инструкции для IM-268S-11

Бренды по названию

Популярные бренды

Bally IM-268S-11, Руководство по обслуживанию

Результаты поиска

Содержание IM-268S-11

Отзывы:

Похожие инструкции для IM-268S-11

Бренды по названию

Популярные бренды