Baldor VS1MX Скачать руководство пользователя страница 58

Страница: 58 / 68

D-2 Options and Kits

MN762

VS1MX Dynamic Braking Resistors

VS1MX Frame B and C drives include built-in braking transistors to aid in applications requiring the ability to stop rapidly.

The brake resistor must be mounted and secured in place. Two wires connect to the + and BR terminals on the power strip

of the size B or the larger enclosure. Refer to Table 4-1 for minimum brake resistor values if a value that is larger than the

stock resistor kit is required.

Table D-3 Dynamic Braking Resistor

Catalog Number

Ohms

Wattage

Frame

VS1MX-R50W200

200

B & C

Table D-4 Minimum Resistor Values

Drive Voltage Rating

Minimum Resistor Value

(Ohms)

Volts

115VAC

230VAC

2 to 5

1.5 to 4

460VAC

2 to 3

1.5 to 2.2

100

7.5 to 10

5.5 to 7.8

When the standard brake resistor kit is used, set P-34=1.

This provides software thermal protection for the standard 200W brake resistor kit.

When special brake resistors are used, set P-34=2.

No software thermal protection is provided in this setting and an external thermal device is required to protect the resistor.

CopyCat Loader

Connects to the RJ45 Port on the front of the VS1MX and allows the upload or download of software parameters.

Table D-5 CopyCat Loader

Catalog Number

Description

VS1ST-CCL

VS1ST and VS1MX RJ45 CopyCat Loader

Option Cards for VS1MX

Provides additional relay outputs for signal and control.

Table D-6 Option Cards

Catalog Number

Description

2ROUT

HVAC

VS1ST-2ROUT

Provides one additional relay output for the drive

VS1ST-HVAC

Provides 2 relays for drive running & drive tripped indicators

VS1ST-LOGHV-11 Provides the ability to accept 100-120VAC control inputs

VS1ST-LOGHV-23 Provides the ability to accept 200-240VAC control inputs

VS1MX Field Bus Gateways

Connects the VS1MX Modbus RTU RS485 communication interface to the field bus gateway.

Table D-7 Field Bus Gateways

Catalog Number

Description

VS1ST-PBUS

Profibus Gateway

VS1ST-DNET

DeviceNet Gateway

VS1ST-ENET

Ethernet Gateway

VS1MX Padlock

Provides a padlock to lockout the disconnect switch.

Table D-8 Lockout Device

Catalog Number

Description

VS1MX-ILOCK

VS1MX Disconnect Switch Padlock

Содержание VS1MX





































































Результаты поиска

Содержание VS1MX

Отзывы:

Похожие инструкции для VS1MX

Бренды по названию

Популярные бренды

Baldor VS1MX, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VS1MX

Отзывы:

Похожие инструкции для VS1MX

Бренды по названию

Популярные бренды