background image

Section

3–4

MN1229

Motor Wiring

Connect the motor leads as follows:

1.

Connect motor phase U to X1-U.

2.

Connect motor phase V to X1-V.

3.

Connect motor phase W to X1-W.

Control Signal Wiring

All wiring from external devices to the control are made at the connectors
shown in Figure 3-1.

The inputs at X3 pins 7, 9, 10, 11 and 12 can be wired for active high or active
low conditions.  Pin 7 is the CREF (Control Input Reference) point.

Active High Definition

If the Control Inputs are to be wired as Active High, CREF is connected to
GND.  When a control input is at +24VDC (range +12VDC to +29VDC), it is
active and when it is at GND it is inactive.  Figure 3-2 shows this relationship.

Active Low Definition

If the Control Inputs are to be wired as Active Low, CREF is connected to
+24VDC (range +12VDC to +29VDC).  When a control input is at GND, it is
active and when it is at +24VDC it is inactive.  Figure 3-2 shows this
relationship.

Table 3-1  Control Inputs

Signal

Connector

Active Condition

Inactive Condition

Enable

X3-9

Control Enable

Control Disabled

CW Limit

X3-10

CW Rotation Enabled

CW Rotation Disabled

CCW Limit

X3-11

CCW Rotation Enabled

CCW Rotation Disabled

Hold

X3-12

Hold function is Active

Hold function is not

active

Содержание DBSC105-AAA-1






































Отзывы: