54464_02-97_A
DIP Switches and Jumpers Definitions
DIP Switchbank A Key
A1
. . . . . . . . . . . . . . . . Test Mode (normally Off)
A2
. . . . . . . . . . . . . . . . In “ON” position, heater can run while any/all high-speed pumps or blowers are running
(High
amperage)
. . . . . . . . . . . . . . . . In “OFF” position, heater is disabled while any high-speed pump or blower is running
(Low
amperage)
A3
. . . . . . . . . . . . . . . . In “ON” position, filter cycles are programmed by duration for non-time capable panels
. . . . . . . . . . . . . . . . In “OFF” position, filter cycles are programmed to start and end times for time capable panels
A4*
. . . . . . . . . . . . . . . . In “ON” position, displays time in 24 hours (military\European time)
. . . . . . . . . . . . . . . . In “OFF” position, displays 12 hour time
A5*
. . . . . . . . . . . . . . . . In “ON” position, displays temperature in Celsius
. . . . . . . . . . . . . . . . In “OFF” position, displays temperature in Fahrenheit
* Sets default for user preferences - only applies when persistent memory is reset (A12 On) during power-up
A6
. . . . . . . . . . . . . . . . In “ON” position, Equipment timeout 30 minutes (4 hours for Pump 1-Low)
. . . . . . . . . . . . . . . . In “OFF” position, Equipment timeout 15 minutes (2 hours for Pump 1-Low)
A7
. . . . . . . . . . . . . . . . In “ON” position, Cleanup Cycle – 30 minutes after spa use/timeout, Pump 1-Low & Ozone or
Circ Pump and Ozone run for 1 hour
. . . . . . . . . . . . . . . . In “OFF” position, no Cleanup Cycle
A8
. . . . . . . . . . . . . . . . In "ON" position, Ozone suppression for one hour after pump/blower button press
A9 and A10. . . . . . . . . . . . . See
Table
for Circ Pump Behavior settings
A11
. . . . . . . . . . . . . . . . In “ON” position
(non-circ mode operation)
Pump 1 is two-speed, Ozone is
ON in Filter & Cleanup Cycles only
(in any circ mode)
Pump 1 is one-speed, Ozone is ON with
circ
pump
. . . . . . . . . . . . . . . . In “OFF” position
(non-circ mode operation)
Pump 1 is two-speed, Ozone is
ON with Pump 1-Low
(in any circ mode)
Pump 1 is two-speed, Ozone is ON with
circ
pump
A12
. . . . . . . . . . . . . . . . Persistent memory reset (normally off) (used when spa is
powering
up)
Circ Pump
A9
A10
Behavior
OFF
OFF
No Circ Pump
or Circ Pump not
plumbed
w/heater
ON
OFF
24 Hours
OFF
ON
24 Hr w/3°F Shut-Off
ON
ON
Acts like Pump 1-Low
(Filter Cycles, Polls)
Jumpers
J37
Jumper on Pins 1 and 2 will power one leg of J12 (Spa Light) at 120 Volts AC.
Jumper on Pins 2 and 3 will power one leg of J12 (Spa Light) at 12 Volts AC.
Note: W9 controls voltage on the other leg of J12 and must be set for the same voltage.
J91
Jumper on 1 Pin only enables Real Time Clock function; use with time capable panels.
Jumper on Pins 1 and 2 disables RTC function; use with non-time capable panels.
DIP Switchbank B Key
B1
. . . . . . . . . . . . . . . In “ON” position, single-speed Pump 2
. . . . . . . . . . . . . . . In “OFF” position, two-speed Pump 2
B2
. . . . . . . . . . . . . . . In “ON” position, Pump 2 enabled
. . . . . . . . . . . . . . . In “OFF” position, Pump 2 disabled
B3
. . . . . . . . . . . . . . . In “ON” position, Blower enabled with Pump 2 low relay
. . . . . . . . . . . . . . . In “OFF” position, Blower disabled
B4
. . . . . . . . . . . . . . . In “ON” position, Fiber and Wheel instead of Spa Light
(if A9 & A10 are both OFF, Fiber uses J2 connector; if either A9 or A10 is ON, X-FOW Kit required to run Fiber)
. . . . . . . . . . . . . . . In “OFF” position, Spa light enabled
B5
. . . . . . . . . . . . . . . In “ON” position, Pump 3 enabled (Jets 3 replaces Blower on Aux panel)
. . . . . . . . . . . . . . . In “OFF” position, Pump 3 disabled
B6
. . . . . . . . . . . . . . . In “ON” position, Alternate Panel layout (ML900 scrunching enabled - ML550 / 700 Jets 3 replaces Blower)
. . . . . . . . . . . . . . . In “OFF” position, Normal Panel layout
WARNING:
•
Setting DIP switches incorrectly may cause abnormal system behavior and/or damage to system components.
•
Refer to Switchbank illustration on Wiring Configuration page for correct settings for this system.
•
Contact Balboa if you require additional configuration pages added to this hot sheet.
