Baker Hughes Panametrics XMT686i Скачать руководство пользователя страница 85

Страница: 85 / 100

Communications Options User’s Guide

Chapter 8. HART Communications

8.3 Flowmeter Software Setup (cont.)

To configure your HART option card analog output using any of the first three methods, follow the instructions in the

appropriate

User’s Manual. During configuration, the choice of parameter must be limited to those listed in Table 11.

To use the HART device for configuration of the analog output, refer to the instructions that came with that device.

Some flowmeter parameters can only be read by the HART device during startup. Therefore, it is recommended that

both the flowmeter and the HART device be rebooted after any reprogramming of the HART option card analog

output. Failure to do so may result in erroneous information or a communication failure between the flowmeter and

the HART device.

8.4 Using the HART Interface

The HART communications option card installed in Panametrics flowmeters has been successfully tested with the

Rosemount 275 Hand-Held Communicator

and the

Rosemount AMS Computer-Based Communications Software

Although some flowmeter functions may be performed using the HART device, many other functions (i.e. data

logging, site file uploading, site file downloading, printing, etc.) must still be programmed by the methods described

in the flowmeter

User’s Manual. This is because the HART protocol was developed for use with simple transmitters

and it cannot handle the multitude of sophisticated functions built into the Panametrics flowmeters.

8.4.1 Unit Types

Due to limitations of the HART protocol, only those unit types listed in Table 11 are acceptable. If a meter parameter is

set to any other measurement units, the HART device displays an

“Unknown Enumerator, Can not resolve” error

message and may terminate communications entirely. In some cases, both the Hart device and the flowmeter may

have to be rebooted to clear the error. To address this potential problem, the flowmeter has been programmed to

force all measurement units to HART compliant units if a HART option card is detected upon startup.

8.4.2 HART Functions

After HART communications has been properly set up, the following flowmeter functions may be accessed using the

HART device:
•

Static temperature and static pressure

Note:

To view the static temperature or pressure for a channel using the HART device, the fixed value for that

parameter must be assigned to that channel at the flowmeter. See your User’s Manual for instructions.

Table 11: Valid HART Parameters and Units

Parameter

English Units

Metric Units

Velocity

ft/sec

m/s

Volumetric

(liquid)

gal/s, gal/m, gal/h, mgal/day, cuf/s, cuf/m, cuf/h,

mcf/day, bbls/s, bbl/m, bbl/h, mbl/d,

acre-inch/day

l/s, l/m, l/h, ml/d, cum/s, cum/m, cum/h,

mcm/d, bbl/s, bbl/m, bbl/h, mbl/d

Volumetric (gas)

acf/m, acf/h, scf/m, scf/h

acm/h, scm/h, scm/d

+Tot, -Tot (liquid) gal, cuf,bbl, acre-in, acre-ft

liter, cum, bbl

+Tot, -Tot (gas)

acf, scf

acm, scm

Mass Flow

lb/s, lb/m, lb/h, mlb/d, ton/m, ton/h, mton/d

kg/s, kg/h, mkg/d, tne/m, tne/h, tne/d

+Mass, -Mass

lb, ton

kg, tne

Power

kbtu/h, kw

mcal/h, kw

+Energy, -Energy

btu, kw-hr

mcal, kw-hr

Temperature

°F

°C

Pressure

psia

bar, bara

Mol Weight

none

NOTE:

“acf” is reported as “normal cubic feet” in HART. Also, “Mega” units (i.e. mgal/day, mcf/day, etc.) are reported

as standard units x 10^6 in HART. For example, 1 mgal is 1x10^6 gal in HART.

Содержание Panametrics XMT686i





































































































Результаты поиска

Содержание Panametrics XMT686i

Отзывы:

Похожие инструкции для Panametrics XMT686i

Бренды по названию

Популярные бренды

Baker Hughes Panametrics XMT686i, Руководство пользователя

Результаты поиска

Содержание Panametrics XMT686i

Отзывы:

Похожие инструкции для Panametrics XMT686i

Бренды по названию

Популярные бренды