Baker Hughes Druck DPI 610 IS Скачать руководство пользователя страница 30

Страница: 30 / 76

20 | DPI 610/615 IS Instruction Manual–English

Chapter

Taking Measurements

4.9 Relief Valve Test (REL VALVE) Task

To carry out a relief valve test, press

TASK

and select

REL VALVE

. Connect the output pressure

port of the instrument to an external system as shown below:

•

To change the pressure units, if required, press

INPUT

and select the required units using

the cursor keys.

•

Close the vent valve and, using the hand-pump or external pressure supply, apply pressure

to the relief valve under test.

•

When the relief valve operates, the maximum recorded pressure indicates the operating

point of the valve.

•

Record the test results.

Note:

The

STORE

key can be used for this purpose. Use right cursor key initially, followed

by up/down keys to enter Snapshot text.

•

Open vent valve to release test pressure.

Note:

If using external pressure supply, isolate supply before opening the vent valve.

External pressure source (indicator only)

Pressure regulator

Relief valve under test

PRESSURE INT

RESET

MAX/MIN

MAXIMUM

MINIMUM

PRESSURE INT

TASK : RELVALVE
SNAPSHOT MODE

Содержание Druck DPI 610 IS







































































Результаты поиска

Содержание Druck DPI 610 IS

Отзывы:

Похожие инструкции для Druck DPI 610 IS

Бренды по названию

Популярные бренды

Baker Hughes Druck DPI 610 IS, Инструкция по эксплуатации

Результаты поиска

Содержание Druck DPI 610 IS

Отзывы:

Похожие инструкции для Druck DPI 610 IS

Бренды по названию

Популярные бренды