Baker Hughes Druck DPI 610 IS Скачать руководство пользователя страница 24

Страница: 24 / 76

14 | DPI 610/615 IS Instruction Manual–English

Chapter

Taking Measurements

•

If applicable, turn on Cal Mode and set-up test parameters as detailed in Section

3.4.

4.3 Pressure Converter (Pressure to Pressure) Task

Select the P-P task from the task menu and connect the Unit Under Test (UUT) to the calibrator

as shown below. Testing a converter requires one pressure to be applied to the unit under test

(UUT) and another (converter output) to be measured. The additional measurement is provided

by the external transducer option.
•

Connect the UUT to the instrument as shown below. Plug the external transducer into the

instrument as shown below:

•

Press the

TASK

key and select the P-P task. Providing the external transducer has been

calibrated and its parameters stored in the instrument, the display will show

External

pressure in the input window and calibrator

Output

pressure in the output window. If an error

message “NO SENSOR OR CAL INVALID” is displayed, this indicates that the external

transducer has not been entered and/or calibrated with the instrument. Refer to Section

8.16

for details of adding an external transducer.

Note:

If an external transducer change is made, switch the calibrator off and then on to load

new transducer data.

•

If required, select the output units as described in Section

3.3.

•

If applicable, turn on Cal Mode and set-up test parameters as detailed in Section

3.4.

External pressure source (indicator instruments only)

Pressure regulator

External pressure source

Pressure to pressure device

External supply

Содержание Druck DPI 610 IS







































































Результаты поиска

Содержание Druck DPI 610 IS

Отзывы:

Похожие инструкции для Druck DPI 610 IS

Бренды по названию

Популярные бренды

Baker Hughes Druck DPI 610 IS, Инструкция по эксплуатации

Результаты поиска

Содержание Druck DPI 610 IS

Отзывы:

Похожие инструкции для Druck DPI 610 IS

Бренды по названию

Популярные бренды