background image

 

 

14 

14 

ELECTRICAL 

 

 

 

 

 

Power Specifications 

Your tool is wired for 115 volts, 60Hz alternating current. Before connecting the tool to the power 
source, make sure the machine is cut off from power source. 
Before switching on the power, you must check the voltage and frequency of the power to see if 
they meet with the requirement, the allowed range for the voltage is ±5%, and for the frequency 
is ±1%. 
 

Considerations 

  Observe local electrical codes when connecting the machine. 

  The circuit should be protected with a time delay fuse or circuit breaker with a amperage 

rating slightly higher than the full load current of machine. 

  A separate electrical circuit should be used for your tools. Before connecting the motor to the 

power line, make sure the switch is in the “OFF” position and be sure that the electric current 
is of the same characteristics as indicated on the tool. 

  All line connections should make good contact. Running on low voltage will damage the 

motor. 

  In the event of a malfunction or breakdown, grounding provides a path of least resistance for 

electric current to reduce the risk of electric shock. This tool is equipped with an electric cord 
having an equipment-grounding conductor and a grounding plug. The plug must be plugged 
into a matching outlet that is properly installed and grounded in accordance with all local 
codes and ordinances. 

 

 

 

CAUTION: 

HAVE ELECTRICAL UTILITIES CONNECTED TO MACHINE BY 

A CERTIFIED ELECTRICIAN!

 

Check if the available power supply is the same as listed on the machine nameplate. 

WARNING:

 Make sure the grounding wire (green) is properly connected 

to avoid electric shock. DO NOT switch the position of the green grounding wire if 
any electrical plug wires are switched during hookup. 

WARNING:

 In all cases, make certain the receptacle in question is 

properly grounded. If you are not sure, have a qualified electrician check the 
receptacle

.

 

Содержание WP-1800B

































Отзывы: