Baileigh Industrial RDB-100 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 44

Baileigh Industrial RDB-100 Скачать руководство пользователя страница 22

19

19

Material Insertion

1. Once the die set is properly installed, the material that matches the die can be inserted (I.E.

1-1/4” tube would go into a die mark D-1250T-R***).

2. Open the counter die quick release assembly and insert the material past the hook arm. The

start of bend mark is engraved with an “O” on the top of the die. Once the material is placed

properly, the counter die slide block assembly can be tightened.

Inserting material to start

Lubricating counter die bending

Important

: Liberally apply lubricant along the counterdie and the 1/2 of the

material that contacts the counter die (A) with a WD-40 style lubricant or equivalent. Do not

lubricate the bending die. Lubricating the bending die will encourage slipping of material in the

bending die.

3. Rotate the quick release counter die assembly until it firmly stops against its stop bolt. In

some cases, usually with pipe the quick release will not close all the way. This is ok, as the

forward foot pedal is activated the material will force its way into the die and bend properly.

A

«
...
20
21
22
23
24
...
»

Содержание RDB-100













































Отзывы:

Нет отзывов