Page 6
For technical questions, please call 1-888-866-5797.
Item 61876
SAFET
y
Op
ERA
TION
MAINTENANCE
SETU
p
Specifications
Power Supply
12VDC Battery
(not included)
Rated Capacity
Dead Pull: 2000 lb.
Marine Pull: 5000 lb.
Rolling Stock Pull: 6000 lb.
Maximum Boat Weight 5,000 lb. – (about 18 ft. Boat
Length)
Drum (Dia. x L)
1" x 3-1/8"
Overall Dimensions
9-1/2" L x 7-1/2" W x 10" H
Wire Rope
Ø3/16" x 30'
Galvanized Steel
Hook Opening
11/16"
Line pull
Line Speed
Amp Draw
lb.
kg.
fpm
mpm
0
0
4.5
1.4
3.1
500
227
3.6
1.1
6
1000
454
2.9
2.3
11
1500
680
2.3
0.9
17
2000
907
1.7
0.5
21
Layer
Rated Line pull
Cable Capacity
lb.
kg.
feet
meters
1
2000
907
4.7
1.4
2
1520
689
10.8
3.3
3
1226
556
18.4
5.6
4
1027
466
27.5
8.4
5
884
401
38.0
11.6
Installation and Setup
Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Note:
For additional information regarding the parts listed in the
following pages, refer to
Parts List and Diagram
on page 14.
Temporary Winch Mounting
1. Use the Adapter Plate (31) to temporarily attach
the Winch to a 2" hitch ball on a vehicle.
2. The Adapter Plate has three pre-mounted Plate
Stud Bolt (38) / Nut (30) / Lock Washer (29) sets.
Push the Bolt heads into the keyhole slots on
the bottom of the Frame Assembly (34) and slide
them into the narrow section of the keyholes.
3. Bolt Adapter Plate to Winch Frame Assembly using
holes provided to lock components together.
4. Place teardrop-shaped hole in
Adapter Plate over hitch ball.
WARNING!
At the start of winching when
using temporary winch mounting, take up
slack slowly and make sure Winch is securely
and properly mounted to hitch ball.
WARNING!
Remove Winch after use. Do not
drive vehicle with Winch temporarily mounted.
permanent Winch Mounting
1. Select a mounting site on the boat trailer, vehicle
bumper, truck bed, or other suitable location.
NOTE:
This Winch is not waterproof and is not intended
for use underwater. Do not mount in locations that are
subject to submersion in water.
Winch can generate extreme forces. Select a location
that can withstand the rated capacity without damage
or weakening. Steel reinforcement plates may be
needed or a certified welder may need to weld on
additional bracing depending on the mounting location.
2. If a mounting plate (not included) is used, it must
be flat and rated to at least the Winch’s capacity.
3. Align the Winch perpendicular to the center
line of the vehicle at the desired location. Use
mounting holes in the Winch Frame Assembly (34)
as a template to mark the spots where holes will
need to be drilled in the installation surface.
4. Before drilling, verify that the installation
surface has no hidden components or
structural pieces that will be damaged.
5. Drill 3/8" holes at the marked locations.
6. Bolt the Winch to the installation surface using
3/8" galvanized/zinc plated bolts, nuts and washers
(not included) of SAE Grade 5 or higher.
Содержание 61876
Страница 1: ......
