Badger Meter ModMAG M1000 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 52

Badger Meter ModMAG M1000 Скачать руководство пользователя страница 32

Programming

Page 30/47

MID_M1000_BA_02_1802

Datalog Period

The data logging period can be adjusted as following:

every 15 min / 1 h / 6 h / 12 h / 24 h

There is a 500 kB memory with about 30.000 data records for data

logging available. The logging capacity is as following (uni-directional

mode):

Period of

15 min

up to 312 days

1 h

up to 1250 days

6 h

up to 20 years

12 h

up to 40 years

24 h

up to 80 years

Start up-, configuration- and Error events which are logged can reduce

the data logging capacity. Logging in Bi-directional mode reduce the

logging capacity by about 40%.

The logging information can be downloaded by a PC program which is

not supplied with the meter.

5.1.7 Info

Serial number

Serial number of the electronic board.

Version

Software version of the device.

Compilat. Date

Date of the software version.

Otp CRC

Checksum of software update

Applicat. CRC

Checksum of application

«
...
30
31
32
33
34
...
»

Содержание ModMAG M1000





















































Отзывы:

Нет отзывов