Bad Boy BRG54FX850 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 34

Bad Boy BRG54FX850 Скачать руководство пользователя страница 18

PAGE 18

PURGING PROCEDURE

Due to the effects air has on the efficiency in hydrostatic

drive applications, it is critical that the air is purged from

the system. These purge procedures should be

implemented any time a hydrostatic system has been

opened to facilitate maintenance or any additional oil has

been added to the system.
1.

Lift the rear tires of the mower off of the ground

and chock your front tires so they do not move.

2.

With the bypass valve open (To open bypass

valve, loosen 1/2 to 1 full turn) and the engine

running, slowly move the handlebars in the

forward and reverse directions (5 to 6 times), as

air is purged from the unit, the oil level will drop.

3.

With the bypass valve closed and the engine

running, slowly move the handlebars in the

forward and reverse directions (5 to 6 times).

Caution: the tires will rotate during this

procedure. Turn off engine. Check the oil level,

and add oil as required.

4.

It may be necessary to repeat steps 1 through 3

until the air is completely purged from the

system. When the tires move forward and

rearward at normal speed purging is complete.

To adjust the tracking on the mower, lengthen or shorten

the push rods shown in Fig. 11 to the right. Lengthening

the push rod will increase the speed of the pump.

Shortening the push rod will decrease the speed of the

pump. Typically tracking adjustments should be made to

the faster side first. Fine tuning adjustments can be made

by turning the adjustment knob, Fig. 12, in front of either

steering arm until the desired effect is achieved.

Neutral

Bypass

Valve

Access

Fig. 10

Fig. 11

Fig. 12

«
...
16
17
18
19
20
...
»

Содержание BRG54FX850



































Отзывы:

Нет отзывов