Bacharach Fyrite Tech 50 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 44

Bacharach Fyrite Tech 50 Скачать руководство пользователя страница 16

Instruction 24-9435

10

Fyrite Tech

3.5.3 CO Channel

Setup

(Model 60 only)

The CO Channel Setup Screen is labeled “CO.”

1. Enter the Setup Mode per Section 3.5.1. If necessary, repeatedly

press the

ENTER

button until “CO” is displayed.

2. Press the

▲

or

▼

button until the desired parameter is dis played.

- no

Sensor disabled. Use this function to turn off the CO chan-
nel if the sensor is bad or missing to avoid the CO sensor
error message from appearing.

- 2Ero

Manual Zero. When the CO channel is set to man u al zero,
the analyzer does not zero the CO sensor to ambient condi-
tions during start up.

- A2

Auto Zero. With the CO channel set to auto zero, the CO
sensor is zeroed to the ambient CO level during start up.

Important:

When using this mode the analyzer must be

turned ON in fresh air, otherwise in cor rect CO read-
ings will occur.

3. Press

ENTER

to move to the next Setup Screen, or press

I/O

to exit

setup.

3.5.4 Exiting the Setup Mode

Press the

I/O

button at any time to exit the Setup Mode and turn OFF the

analyzer. Note that the last displayed parameter is automatically saved in
memory.

«
...
14
15
16
17
18
...
»

Содержание Fyrite Tech 50













































Отзывы:

Нет отзывов