11. Explanation of the remote control button functions
11a. In the initialisation period
During initialization phase/self test cycle
Lights can be set to on or off status during initialization(60
Seconds) by using INI OFF/ON mode.
12 h Light ON/OFF (party function)
Activated by “Light“ - push button
Deactivated by “Reset“- push button (default)
Corridor function
Activated by “outside“- push button
Deactivate by “inside“- push button (default)
Forced shutdown
Activated by “sun“ - push button
Deactivate by “moon“- push button (default)
11b. In opened state
This push button opens the detector and the following functions
can then be programmed.
Attention:
The detector is closed automatically:
• after every voltage recovery
• after 3 minutes
The state changes to “closed“.
In the first 5 seconds, the white LED flashes every 0.5 seconds.
During this time, sabotage protection can be activated.
The device distinguishes between 2 procedures:
•
Reading in with lighting switched on:
The switch-on value is determined automatically.
Determining the switch-on value:
1. Press the “eye“ push button
2. Switch off the light (2 seconds later)
3. Read in the brightness
4. Switch-on value = Read brightness
•
Reading in with lighting switched off:
When the push button is pressed, the current brightness
is specified as the switch-on value. The switch-off value is
determined automatically.
If the brightness has been modified, the switch-off threshold is
recalculated.
Each time the push button is pressed, the device increases the
current switch-on value in increments of 20 Lux for a current
switch-on value of < 100 Lux and in increments of 50 Lux for a
current switch-on value of > 100 Lux.
Standard sensitivity for most applications
Reduced sensitivity for outdoor applications
When the pulse function of channel 1 is active, a pulse of 1 sec.
is generated every 9 sec. If the pulse function is activated via
remote control, the pause between 2 pulses can be modified.
After activating the function via the “Pulse“ push button, select
the desired time within 5 sec.:
��
���
5
min
= 9 sec.,
��
���
10
min
= 10 sec.,
��
���
15
min
= 15 sec.,
��
���
30
min
= 30 sec.
The impulse function of channel 2 depends only on motion !
After each movement the HVAC channel is activated for
2.5 sec.; time delay starts afterwards for 9 sec.
The “Test“ push button can be used to set the LED ON/OFF
function. To do this, hold down the push button for 3 sec.
Please note
that in the open state and in test mode, the LED
indicators are always ON.
Twilight switch function (CdS)
If the CdS function is active, the detector acts as a simple
twilight switch. Only the brightness can be set in this mode.
Movements are no longer indicated by the red LED.
Push button acknowledgement:
Each push of a button is indicated by lamp acknowledgement
and by the white LED.
“Light ON“ status: OFF/ON (approx. 0.5 sec. each)
“Light OFF“ status: ON/OFF (approx. 0.5 sec. each)
+
In case the sensing area of the
LUXOMAT
®
PD4-M-2C is too large or areas are being covered
that should not be monitored, the range can be
reduced or limited through use of the enclosed
masking clips.
17. Exclude sources of interferences
Type
SM
FC
FM
PD4-M-2C (Master)
92140
92148
92255
PD4-S (Slave)
92142
92254
92163
LUXOMAT
®
Remote control:
IR-PD (incl. wall bracket)
92160
IR-PD-2C (incl. wall bracket)
92475
Accessory:
BSK Ball basket guard
92199
18. Article / Part nr. / Accessory
1.
If the switch-on threshold has been modified by the poten-
tiometer or remote control, the switch-off threshold stored in
the EEPROM is deleted and is then recalculated on the next
activation.
Determining the switch-off value
1. Switch on for 5 min. with dark and motion
2. Light OFF for 2 sec.
3. Internal calculation of the switch-off value
2.
If the eye push button is pressed, the switch-off threshold is
recalculated. See also Remote control –> Eye section
3.
Switch-off delay
If the determined switch-off threshold is exceeded during
operation, the detector only switches off after a delay of approx.
15 minutes. This compensates for any brief fluctuations in the
brightness.
12. Switch-off threshold brightness
16. Range of Coverage
PD4-M-2C
12 h Light ON/OFF activated
Light ON:
Push button pressed briefly: Light OFF as long as Lag time
Push button held down: 12 h OFF
Light OFF:
Push button pressed briefly: Light ON as long as Lag time
Push button held down: 12 h ON
12 h Light ON/OFF deactivated
Light ON:
Push button pressed briefly: Light OFF as long as Lag time
Push button held down: Light OFF as long as Lag time
Light OFF:
Push button pressed briefly: Light ON as long as Lag time
Push button held down: Light ON as long as Lag time
13b. Behaviour of external push button/IR “Light“
Activation of light for 12 h via mains interruption
1. Interrupt current
2. Apply current for 2 to 5 sec.
3. Interrupt current again
4. Apply current
5. Detector is now ON for 12 h
Exiting sabotage
1. Interrupt current
2. Apply current for 30 to 60 sec.
3. Interrupt current again
4. Apply current
5. Detector is in simple closed state
230 V AC permanently at the slave input
If 230 V AC is applied at the slave input for longer than 10 sec., the
light is switched on permanently. When the 230 V is removed, the
light is switched off and automatic mode is activated.
230 V AC for 1 - 3 sec. at push button connection S
If 230 V AC is applied for 1 - 3 sec. at push button connection S, this
is interpreted as a slave signal at slave connection R. This ensures
that the detector is compatible with previous versions.
14. Other functions
15. Fully automatic and semi automatic mode
(see functions IR-PD-2C)
Fully automatic operation
In this operating mode, the lighting switches automatically on and off
for increased comfort, depending on presence and brightness.
Channel 1 switches on in the event of motion if “dark“ is detected.
Semi automatic operation
In this operating condition, in order to gain increased savings, the
lighting is energized only after being manually switched on.
Switch-off takes place automatically or manually.
The semi automatic mode basically behaves like the fully automatic
one. However, the difference is that switching-on must always be
carried out manually!
As many (NO-contact) buttons as desired can be wired in parallel on
the “S” button input (ON/OFF).
Triggering in semi automatic mode:
If the detector switches off in semi
automatic mode (lag timer elapsed), the detector is switched on again
within 10 sec. by motion (despite semi-automatic mode).
HA
ON/OFF
Forced shutdown active
Light OFF:
Light OFF: Push button pressed briefly: Light ON for approx.
30 min., then forced shutdown if the set brightness is still exceeded.
13c. Behaviour of external push button/IR
“Forced shutdown“
The “Corridor“ and “Light ON/OFF“ functions are mutually
exclusive. If both are activated, the detector performs the corridor
function.
The behaviour when the push button is pressed is defined as follows:
Corridor function activated
Light ON:
Push button pressed briefly (0,1 - 1sec.): Light OFF -> Active after
5 sec.
Push button held down (> 3 sec.): Light OFF -> Active after 5 sec.
Light OFF:
Push button pressed briefly: Light ON as long as Lag time
Push button held down: Light ON as long as Lag time
13a. Behaviour of external push button/IR “Light“
walking towards
walking across
seated
1
2
3
PI R
CdS
24 m
8 m
6,40 m
24 m
360°
2,50 m
2
3
1
1000
20
SM
FC
FM
