B.C. Air PA-28-140 Скачать руководство пользователя

Страница: 1 / 38

Every dollar helps!

These manuals are the culmination of more then 10 years of design

and publication and formally sold for $10.00 each. With 54 different

manuals available, that’s a $540.00 value.

Now, due to the worldwide economic collapse, they are my gift to you.

My hope is that you will enjoy these great little airplanes as much as I

have enjoyed designing them for you.

You may build as many planes as you like.

Sell your planes, or give them away.

Tell ALL your airplane loving friends to come to the site and get as

many of the manuals as they like.

If you enjoy these planes, please help to ensure this site stays on-line

and these airplane manuals remain available for all to enjoy. Any

amount you donate is greatly appreciated.

May God bless you and keep you safe.

Thank You & Enjoy!

Wayne

Содержание PA-28-140







































Результаты поиска

Содержание PA-28-140

Отзывы:

Похожие инструкции для PA-28-140

Бренды по названию

Популярные бренды

B.C. Air PA-28-140, Руководство пользователя

Результаты поиска

Содержание PA-28-140

Отзывы:

Похожие инструкции для PA-28-140

Бренды по названию

Популярные бренды