B. Braun 871 5416 Скачать руководство пользователя страница 23

Страница: 23 / 86

Infusomat® fmS 2.3 gb

2 - 1

2 -

Software

Software Update

Designation

Ord. No.

Update kit IFMC02003 . . . . . . . . . . . . . . . . . . . . . . . . . 3450 645A

Update kit IFMe02004 / IFME03004 . . . . . . . . . . . . . . 3450 645C

Update kit IFMe02005 / IFME03005 . . . . . . . . . . . . . . 3450 645D

Update kit IFMe02006 / IFME03006 . . . . . . . . . . . . . . 3450 645E

Update kit IFMe02007 / IFME03007 . . . . . . . . . . . . . . 3450 645F

MFC interface line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0871 1661

The higher digit always replaces the lower digit for the revision

level, e.g. IFME02007 replaces IFME02006.

Units with an old software version (e.g. IFMC02001) can be up-

dated to the new software version IFME03007.

When the software group changes the unit functions are

changed, too. Therefore unit users must be informed (e.g. instruct

the user and exchange the instructions for use – software coding

(e.g. IFME) is to be found on the cover page of the instructions for

use.)

Note

Do not use an update program on Windows NT systems.

Note

Mark the unit after having updated the software! The new soft-

ware version must be clearly recognizable.

Only update from old to new software versions, never in reverse

order (e.g. never update from IFMC02003 to IFMC02001!).

All units used in one ward should have the same software status

and basic setup to avoid operator mistakes.

Note

Software updates must be reported to B. Braun for registration.

Observe the notes of the update program and the supplements!

Fig.: 2 - 1 Coding

Position

Digit

M E 0 3 0 0 7

Revision level

Hardware identification

Software group

Infusomat® fmS

2 - 8

Содержание 871 5416























































































Результаты поиска

Содержание 871 5416

Отзывы:

Похожие инструкции для 871 5416

Бренды по названию

Популярные бренды

B. Braun 871 5416, Руководство по обслуживанию

Результаты поиска

Содержание 871 5416

Отзывы:

Похожие инструкции для 871 5416

Бренды по названию

Популярные бренды