manualshive.com logo in svg

B+B SmartWorx SPECTRE v3 LTE, Руководство пользователя, Страница: 9 / 50

Поделиться
Скачать
B+B SmartWorx SPECTRE v3 LTE Скачать руководство пользователя страница 9

1. SAFETY INSTRUCTION

1. Safety Instruction

Please, observe the following instructions:

•

THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B,
C, AND D HAZARDOUS LOCATIONS, OR NON-HAZARDOUS LOCATIONS ONLY.

•

WARNING – EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT UNLESS
POWER HAS BEEN REMOVED OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.

•

WARNING – EXPLOSION HAZARD – SUBSTITUTION OF ANY COMPONENTS MAY
IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.

•

CET ÉQUIPEMENT EST CONVENABLE EN CLASSE 1, DIVISION 2, GROUPES A, B,
C, ET D ENDROITS DANGEREUX OU ENDROITS NON DANGEREUX SEULEMENT.

•

AVIS – RISQUE D’EXPLOSION – NE DÉCONNECTEZ PAS L’ÉQUIPEMENT, SAUF
SI L’ALIMENTATION A ÉTÉ COUPÉE OU SI L’ENVIRONMEMENT EST CLASSÉ NON
DANGEREUX.

•

AVIS – RISQUE D’EXPLOSION - SUBSTITUTION DE TOUTE COMPOSANTE RIS-
QUERAIT LA QUALITÉ POUR CLASSE 1, DIVISION 2.

•

The router must be used in compliance with all applicable international and national laws
and in compliance with any special restrictions regulating the utilization of the router in
prescribed applications and environments.

•

To prevent possible injury and damage to appliances and to ensure compliance with
all relevant provisions, use only the original accessories. Unauthorized modifications or
the use of unapproved accessories may result in damage to the router and a breach of
applicable regulations. Unauthorized modifications or use of unapproved accessories
may void the warranty.

•

The router can not be opened.

•

Turn off the router and disconnect it from power supply before handling of the SIM card.

•

Caution!

The SIM card could be swallowed by small children.

•

Input voltage must not exceed 60 V DC max.

•

Do not expose the router to extreme ambient conditions. Protect the router against dust,
moisture and high temperature.

•

The router should not be used in locations where flammable and explosive materials
are present, including gas stations, chemical plants, or locations in which explosives
are used. We remind the users of the duty to observe the restrictions concerning the
utilization of radio devices at such places.

1

Содержание SPECTRE v3 LTE



















































Отзывы:

Нет отзывов