manualshive.com logo in svg

B+B SmartWorx SPECTRE v3 LTE, Руководство пользователя, Страница: 26 / 50

Поделиться
Скачать
B+B SmartWorx SPECTRE v3 LTE Скачать руководство пользователя страница 26

5. ROUTER DESIGN

5.8.4

SIM card reader

Two SIM card readers for 3 V and 1.8 V SIM cards are placed on the rear panel of the

router. For getting the router to work is necessary to insert an activated SIM card with an
unblocked PIN code. The SIM cards might be of different adjusted APN (Access Point Name).

Changing the SIM card:

•

Before handling of the SIM card disconnect the router from power supply!

•

Use a plastic opening tool, or your fingernail, to press the SIM card slightly deeper into
its slot until you hear a click.

•

After the click, release the card and it will pop out of its slot.

•

Remove the SIM card and push any other SIM card into the slot until it clicks in place.

Figure 28: SIM cards

5.8.5

MicroSD card reader

The microSD card reader is placed on the rear panel of the router (the third slot). This card

reader allows the router to operate with memory cards microSD. Technical specifications are
stated in the table below.

Technical specifications of microSD card

Supported technologies

SDHC, SDXC

Supported capacity

SDHC
SDXC

up to 32 GB
from 32 GB to 64 GB

Table 11: Technical specifications of microSD card

18

Содержание SPECTRE v3 LTE



















































Отзывы:

Нет отзывов