B+B SmartWorx IE-MultiWay Скачать руководство пользователя страница 64

Страница: 64 / 66

-MultiWay

FIBER OPTIC CLEANING GUIDELINES

Fiber Optic transmitters and receivers are extremely susceptible to

contamination by particles of dirt or dust, which can obstruct the optic path and

cause performance degradation. Good system performance requires clean

optics and connector ferrules.

1. Use fiber patch cords (or connectors, if you terminate your own fiber)

only from a reputable supplier; low-quality components can cause many

hard-to-diagnose problems in an installation.

2. Dust caps are installed at the factory to ensure factory-clean optical

devices. These protective caps should not be removed until the moment

of connecting the fiber cable to the device. Should it be necessary to

disconnect the fiber device, reinstall the protective dust caps.

3. Store spare caps in a dust-free environment such as a sealed plastic

bag or box so that, when reinstalled, they do not introduce any

contamination to the optics.

4. If you suspect that the optics have been contaminated, alternate

between blasting with clean, dry, compressed air and flushing with

methanol to remove particles of dirt.

Содержание IE-MultiWay



































































Результаты поиска

Содержание IE-MultiWay

Отзывы:

Похожие инструкции для IE-MultiWay

Бренды по названию

Популярные бренды

B+B SmartWorx IE-MultiWay, Руководство пользователя

Результаты поиска

Содержание IE-MultiWay

Отзывы:

Похожие инструкции для IE-MultiWay

Бренды по названию

Популярные бренды