B+B SmartWorx IE-MultiWay Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 66

background image

IE

-MultiWay

52

CONFIGURATION FILE SAVE/RESTORE FUNCTION

Requirements

The Configuration File Save/Restore Function allows a user to backup all the

configuration settings of a unit. With this backup, a user can restore settings to a

unit if necessary or use the backup to apply the same settings to a different unit.
All configurable managed objects are saved in a configuration file that is stored in

the unit’s Large File Area. This includes all configurable settings such as VLAN

and IP Address configurations and SNMP agent settings. The configuration file

can be transferred from the unit to a PC and saved to disk via the iView

2

(iConfig

view) protocol. The configuration file can be transferred from a PC to a unit of the

same type via iView

2

(iConfig view) or TFTP

into the unit’s Large File Area. After

the transfer is complete, the unit copies the configuration to flash and reboots.
The configuration file’s contents is device-type specific and can be identified by

iView

2

(iConfig view) as a configuration file as well as to what type of device it is

applicable to.

SAVING A CONFIGURATION FILE TO DISK

From the Administration Tab in iView

2

(iConfig view) click the

Save

Configuration

button:

«
...
50
51
52
53
54
...
»

Содержание IE-MultiWay



































































Отзывы:

Нет отзывов

Похожие инструкции для IE-MultiWay

MediaLounge DSM-520

Бренд: D-Link Страницы: 2

Dial-to-IP 5301-DC

Бренд: Accelerated Страницы: 26

MaitreView 4KLite

Бренд: AVLink Страницы: 10

Бренд: Vanco Страницы: 16

Бренд: VXI Страницы: 57

OBID i-scan ID ISC.ANT.PS-A

Бренд: Feig Electronic Страницы: 28

Бренд: Agilent Technologies Страницы: 70

Бренд: ILX Lightwave Страницы: 16

Бренд: ZIPPER MASCHINEN Страницы: 52

Бренд: Fronius Страницы: 135

Бренд: Samlexpower Страницы: 20

Бренд: Extron electronics Страницы: 2

CIS-N-MPPT-LED 85/15

Бренд: Phocos Страницы: 79

SinePower SP150

Бренд: Waeco Страницы: 96

Бренд: SHOWTEC Страницы: 16

JNTHBCBA0001BEAU

Бренд: TECO Страницы: 98

3D Vision Encoder

Бренд: ADJ Страницы: 4

S1F76540M0C Series

Бренд: Epson Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды