B+B Sensors 0555 0035-01 Скачать руководство пользователя страница 10

Страница: 10 / 10

TxRail-USB Temperature Transmitter
0555 0035-01, 0555 0035-02

0141 0315-951 27.09.2021

B+B Thermo-Technik GmbH | Heinrich-Hertz-Str. 4 | D-78166 Donaueschingen

Seite

von

Technische Änderungen vorbehalten

Fon +49 771 83160 | Fax +49 771 831650 | [email protected] | bb-sensors.com

any measurement errors. See item Zero Correction in the chapter CONFIGURATION of this manual.

The user must choose the most suitable sensor and range to the process. The chosen range must not exceed the maximum range of

measurement defined for the sensor and should not be smaller than the minimum range for the same sensor.

It is important to note that the transmitter accuracy is based on the maximum range of the sensor used, even when a narrower

range is programmed. Example:



The Pt100 sensor in the range 0 to 100 °C and accuracy of 0.12 %, the maximum error will be 1.02 °C (0.12 % de 850 °C).



The Pt100 sensor in the range 500 to 600 °C and accuracy of 0.19 %, the maximum error will be 1.61 °C (0.19 % of the 850 °C).

Note

: When measurements are made at the transmitter, see if the Pt100 excitation current required by the calibrator is compatible with the

Pt100 excitation current used in the transmitter: 0.8 mA

UESTIONS

For further Information about this or other products of B+B Thermo-Technik GmbH please do not hesitate to contact us at:

B+B Thermo-Technik GmbH

Heinrich-Hertz-Straße 4

78166 Donaueschingen

Deutschland

Tel.: +49 771 83160

Fax: +49 771 831650

E-Mail: [email protected]

www.bb-sensors.com

Содержание 0555 0035-01











Результаты поиска

Содержание 0555 0035-01

Отзывы:

Похожие инструкции для 0555 0035-01

Бренды по названию

Популярные бренды

B+B Sensors 0555 0035-01, Руководство по эксплуатации

Результаты поиска

Содержание 0555 0035-01

Отзывы:

Похожие инструкции для 0555 0035-01

Бренды по названию

Популярные бренды