General Operation
Installation
AM/FM Tuner Operation
CD Operation*
Installation
Before You Start
• Consult a qualified technician for instructions. Axxera always recommends
professional installation.
• Disconnect negative battery terminal.
• Remove trim ring from unit (if installed).
• Remove 2 transit screws located on top of the unit (if applicable).
• Insert the removal keys, and remove the mounting sleeve from the head unit.
Note
: Most vehicles require an installation kit, wiring harness and/or antenna
adapter (all sold separately) to properly install the head unit in the vehicle.
Installation Process
1. Carefully remove the existing head unit.
2. Connect wiring harness. Consult a qualified technician if you are unsure.
3. Mount the head unit using the mounting sleeve or ISO brackets (depending on
your vehicle’s dashboard).
4. Connect wiring harness and antenna. Test the head unit for correct operation.
5. Slide into mounting sleeve to secure, or mount the ISO brackets to the vehicle.
6. Snap trim ring into place.
Wiring Connections
The chart below defines the connection for each wire in the wiring harness.
Color
Connection
Red
12V Ignition / Accessory
Yellow
12V Battery / Memory
Black
Ground
Blue
Power Antenna / Amp Turn-on
Grey
Right Front (+)
Grey/Black
Right Front (-)
White
Left Front (+)
White/Black
Left Front (-)
Purple
Right Rear (+)
Purple/Black
Right Rear (-)
Green
Left Rear (+)
Green/Black
Left Rear (-)
Quick Start Guide
This Quick Start Guide provides basic instructions
for using your Axxera Receiver.
To download the complete Owner’s Manual please
visit www.
axxeraaudio.com/support/manuals.php
and type in the product’s model number
or call customer service at 1-866-382-5476.
th
in
k
be
fore you p
rin
t
Step 1:
Insert the mounting sleeve into the
installation kit or dashboard.
Step 2:
Bend multiple mounting tabs around
the mounting sleeve until the
mounting sleeve is secure.
Step 3:
Connect all wiring harnesses and
slide the head unit into the mounting
sleeve until it clicks into place.
Using the existing brackets or the
brackets supplied with the installation
kit, mount the brackets to the sides of
the head unit with the screws supplied
with the head unit.
* Not an available feature on all head units.
To download the complete Owner’s Manual for your radio,
please visit www.axxeraaudio.com/support/manuals.php.
* Not an available feature on all head units.
To download the complete Owner’s Manual for your radio,
please visit www.axxeraaudio.com/support/manuals.php.
* Not an available feature on all head units.
To download the complete Owner’s Manual for your radio,
please visit www.axxeraaudio.com/support/manuals.php.
* Not an available feature on all head units.
To download the complete Owner’s Manual for your radio,
please visit www.axxeraaudio.com/support/manuals.php.
* Not an available feature on all head units.
To download the complete Owner’s Manual for your radio,
please visit www.axxeraaudio.com/support/manuals.php.
* Not an available feature on all head units.
To download the complete Owner’s Manual for your radio,
please visit www.axxeraaudio.com/support/manuals.php.
Power On/Off
Faceplate
Removal
Changing
Modes
Volume
Mute
Auxiliary Inputs
Reset
Setting the
Clock
Display
Menu
Press the button to turn the unit on. Press
again to turn unit off.
Press the release button and pull away from the
left side to remove. To re-install, insert right side of
faceplate first then push left side to secure.
Press
SOURCE
to cycle through available
operating modes.
Adjust volume using volume knob.
Press to silence the audio. Press again to
resume listening at the previously selected volume.
Insert a 3.5mm cable in the units front AUX port, or
RCA cables into the rear AUX-IN connectors.
Press the
RESET
button to reset the unit back to
the factory settings if abnormal operation occurs.
The reset button is located behind the front panel.
With the unit on, press and hold
DISP
until the
clock begins to flash, then release. Press
TUNE
nn
to adjust the hours and
TUNE
ll
to adjust
the minutes. Press
DISP
momentarily to save the
selected time.
Press
DISP
to toggle display between various
displayed information.
Press
MENU
to access the audio and setup menu
options.
Seek Tuning
Manual Tuning
Band
*Storing
Presets
*Recalling
Presets
*Storing
Presets
(AXD330 only)
*Recalling
Presets
(AXD330 only)
Insert CD
Eject CD
Track Select
Fast Forward/
Reverse
Pause
Intro
Repeat
Random
CD-R/CD-RW
Compatibility
Press
TUNE
nn
or
TUNE
ll
for more than
one second to seek to the next strong station.
Press
TUNE
nn
or
TUNE
ll
momentarily to
move radio frequency up or down one step at a
time. Press and hold to advance quickly.
Press
BAND
to select between FM1, FM2, FM3,
AM1 and AM2 bands. Up to six presets can be
programmed for each band, enabling up to 18
FM stations and 12 AM stations to be stored in
memory.
Select the desired band and station. Press the
F
(function) button, turn the volume knob until the
desired preset number is highlighted, then press
SELECT
to store the preset.
Press the
P+
or
P-
buttons to cycle through the
1-6 presets in the current band.
Select the desired band and station. Press and
hold the desired 1-6 preset button for more than
two seconds. When stored, the preset number will
appear in the display.
Stored stations can be recalled instantly by
pressing the corresponding 1-6 preset button.
Press the
OPEN
button to open the front panel.
With the label facing up, insert a standard size CD
into the CD slot. The CD will automatically begin
playback.
Press
EJECT
to eject the CD. The unit will change
to previous mode of operation.
Press
TUNE
ll
to skip to the beginning of the
next track. Press
TUNE
nn
to return to the
beginning of the current track. Pressing
TUNE
nn
again skips to the beginning of the previous
track.
Press and hold
TUNE
ll
or
TUNE
nn
to fast
forward or reverse a track.
Press
l
/ II
to temporarily stop CD playback.
Press
l
/ II
again to resume playback.
Press
F
or
INT*
to play the first 10 seconds of
each track.
Press
F
or
RPT*
to continuously repeat the
selected track.
Press
F
or
RDM*
to play all the tracks in random
order.
Some CD-Rs and CD-RWs may be incompatible
with this unit, depending on media type and
recording method. Refer to the online owner’s
manual for details.
Mounting the Head Unit:
ISO mounting
Mounting the Head Unit:
Typical DIN mounting
Limited One-Year Warranty
This warranty gives you specific legal rights. You may also have other rights which
vary from state to state. Dual Electronics Corp. warrants this product to the original
purchaser to be free from defects in material and workmanship for a period of one
year from the date of the original purchase. Dual Electronics Corp. agrees, at our
option, during the warranty period, to repair any defect in material or workmanship
or to furnish an equal new, renewed or comparable product (whichever is deemed
necessary) in exchange without charges, subject to verification of the defect or
malfunction and proof of the date of purchase. Subsequent replacement products are
warranted for the balance of the original warranty period.
Who is covered?
This warranty is extended to the original retail purchaser for
products purchased and used in the U.S.A.
What is covered?
This warranty covers all defects in material and workmanship
in this product. The following are not covered: installation/removal costs, damage
resulting from accident, misuse, abuse, neglect, product modification, improper
installation, incorrect line voltage, unauthorized repair or failure to follow instructions
supplied with the product, or damage occurring during return shipment of the
product.
What to do?
1. Before you call for service, check the troubleshooting guide in your owner’s manual.
A slight adjustment of any custom controls may save you a service call.
2. If you require service during the warranty period, you must carefully pack the
product (preferably in the original package) and ship it by prepaid transportation
with a copy of the original receipt from the retailer to an authorized service center.
3. Please describe your problem in writing and include your name, a return UPS
shipping address (P.O. Box not acceptable), and a daytime phone number with
your shipment.
4. For more information and for the location of the nearest authorized service center
please contact us
t
oll-free at 1-866-382-5476 or by email at [email protected].
Exclusion of Certain Damages:
This warranty is exclusive and in lieu of any
and all other warranties, expressed or implied, including without limitation the
implied warranties of merchantability and fitness for a particular purpose and any
obligation, liability, right, claim or remedy in contract or tort, whether or not arising
from the company’s negligence, actual or imputed. No person or representative is
authorized to assume for the company any other liability in connection with the sale
of this product. In no event shall the company be liable for indirect, incidental or
consequential damages.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Warning
: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
Note
: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Dual Electronics Corp.
Toll Free: 1-866-382-5476
www.axxeraaudio.com
©2013 Dual Electronics Corp. All rights reserved.
NSA0113-V01
Operation of iPod/iPhone
Operation of iPod/iPhone
Connect an iPod/
iPhone Device
(sold separately)
Device
Compatibility
Song Select
Fast Forward
and Reverse
Pause
Repeat
Random
Intro
To play music from an iPod/iPhone device, connect the
USB cable (included with your iPod/iPhone device) to the
unit’s USB port. Playback will begin automatically.
Refer to the online Owner’s Manual for a complete list of
compatible iPod/iPhone devices.
Press
ll
to skip to the next song. Press
nn
to return
to the beginning of the current song. Pressing
nn
again
skips to the beginning of the previous song.
Press and hold
ll
or
nn
to fast forward or reverse a
song.
Press
l
/ II
to temporarily stop playback.
Press
l
/ II
again to resume playback.
Press
F
or
RPT*
to enter the Repeat menu, then turn the
volume knob to select one of the following options:
• Off - Repeats all tracks.
• Current Song - Repeats selected track.
Press
F
or
RDM*
to enter the Random menu, then turn
the volume knob to select one of the following options:
• Off - Cancels the RDM function.
• All Songs - Plays all tracks in random order.
• Current Album - Plays all tracks in the selected album in
random order.
Press
F
or
INT*
to enter the Intro menu, then turn the
volume knob to select one of the following options:
• Off - Cancels the INT function.
• On - Plays first 10 seconds of each track.
Music Search
Manual Control
for iPod
Press
SELECT
, and the main search menu will
appear.
Select a Category:
Turn the
volume knob
to
select between artists, albums, songs, playlists,
podcasts and audiobooks. Press
SELECT
to select
the desired search category and/or subcategory.
Step Backwards:
Press
BACK
to return to the
previous menu or to exit the search menu when
the main menu is shown.
Playing a Song:
Navigate to the desired song/
podcast/audiobook, and press
SELECT
to begin
playback.
When “MANUAL” control is selected from the
Setup Menu, the iPod or iPhone device can be
controlled directly from the device’s interface. All
functions except for volume can be used from the
iPod or iPhone device.
Note
: The firmware of the iPod/iPhone must be
updated to the latest version to be compatible with
manual control mode.
Note
: Not all iPod/iPhone devices are compatible
with manual control mode.
Pandora
®
Operation
* Not an available feature on all head units.
To download the complete Owner’s Manual for your radio,
please visit www.axxeraaudio.com/support/manuals.php.
Car Audio
Mounting Sleeve
Dashboard or Installation Kit
Mounting Sleeve
Dashboard or Installation Kit
Mounting Tabs
New
Radio
Existing
Brackets
Decorative
Bezel
Mounting Sleeve
Dashboard or Installation Kit
Head Unit
MP3 / WMA Operation
Playing MP3/
WMA Files
Track Select
Fast Forward and
Reverse
Pause
Folder Access
Repeat
Random
Intro
To play MP3/WMA files, insert a data CD* or USB device
containing MP3/WMA files.
Press
TUNE
ll
to skip to the beginning of the next song.
Press
TUNE
nn
to return to the beginning of the current
song. Pressing
TUNE
nn
again skips to the beginning of
the previous song.
Press and hold
TUNE
ll
or
TUNE
nn
to fast forward
or reverse a track.
Press
l
/ II
to temporarily stop playback.
Press
l
/ II
again to resume playback.
Press to select the next folder. Press to select the
previous folder. Folder access is only available on discs or
devices with more than one folder.
Press
F
or
RPT*
to enter the Repeat menu, then turn the
volume knob to select one of the following options:
• Current Song - Continuously repeats selected track.
• Current Folder - Continuously repeats all files in folder.
Press
F
or
RDM*
to enter the Random menu, then turn
the volume knob to select one of the following options:
• Off - Cancels RDM function.
• All Songs - Plays all tracks in random order.
• Current Folder - Plays all tracks in folder in random
order.
Press
F
or
INT*
to enter the Intro menu, then turn the
volume knob to select one of the following options:
• Off - Cancels the INT function.
• All Songs - Plays first 10 seconds of each track.
• Current Folder - Plays first 10 seconds of each track in
the selected folder.
Requirements
USB Connection
Changing
Stations
Shuffle
Skipping Tracks
Play/Pause
Thumbs Up
Thumbs Down
Device
Compatibility
Troubleshooting
Control for Pandora requires:
• An iPhone device with a reliable data connection, or an
iPod touch that is connected to wireless internet.
• The Pandora App installed on the iPhone/iPod device.
• An active account with Pandora. Sign up at www.pandora.
com.
• The USB sync cable that came with your iPod/iPhone
device.
Connect an iPod touch or iPhone device (required, sold
separtely) to the USB port, using the USB sync cable
included with your iPhone device.
Press
SELECT
to display the stations menu. Turn the
volume knob
to cycle through the list of stations, then press
SELECT
when the desired station is highlighted.
Note
: Stations must be created on your account prior to
connecting your iPod/iPhone device to the head unit.
Press
SELECT
to display the stations menu. Choose “Quick
Mix” from the stations menu to shuffle songs from all of
your stations.
Press
ll
to skip the current song.
Press
l
/ II
to temporarily stop playback.
Press
l
/ II
again to resume playback.
Press to customize the station to play more songs like
the currently playing song.
Press to customize the station to play songs that are
different from the currently playing song.
Refer to the online Owner’s Manual for a complete list of
compatible iPod/iPhone devices.
Note
: Pandora may use large amounts of data and carrier
data charges may apply. For best results, we recommend
that you connect your device to trusted WiFi networks when
available.
Fuse
:
When replacing the fuse, make
sure new fuse is the correct type
and amperage. Using an incorrect
fuse could damage the radio.
Tip:
When a suitable ground wire is
not present in the vehicle wiring
harness, connect the black ground
wire to the vehicle chassis.
