Axis F34 Скачать руководство пользователя страница 9

Страница: 9 / 64

AXIS F34 Main Unit

Hardware Overview

Status LED

Indication

Green

Steady green for normal operation.

Amber

Steady during startup and when restoring settings.

Note

The Network LED can be disabled so that it does not flash when there is network traffic. To configure, go to

Setup > System

Options > Ports & Devices > LED

. See the online help for more information.

Network LED

Indication

Green

Steady for connection to a 100 Mbit/s network. Flashes for network activity.

Amber

Steady for connection to a 10 Mbit/s network. Flashes for network activity.

Unlit

No network connection.

Power LED

Indication

Green

Normal operation.

Amber

Flashes green/amber during firmware upgrade.

Sensor Units

It is recommended to connect the sensor units to the main unit before powering the main unit. If you disconnect a sensor unit, and
connect a different sensor unit, it may be necessary to restart the main unit.

Shorten Sensor Unit Cable

Note

The sensor unit’s cable cannot be extended or split.

The sensor unit is delivered with a cable. To shorten the cable follow these steps:

1. Cut the cable to the desired length. Measure from the sensor unit.

2. Strip the plastic outer coating from the end of the cable.

3. Peel back the shield.

4. Flatten the colored wires in the order described below.

Brown

White/brown

Not used

White/blue

Blue

5. Insert the wires all the way into a shielded 6P6C RJ12 connector.

NOTICE

TICE

Make sure that the wires stay in the correct order and that the cable shield makes good contact with the connector shield.

Содержание F34

































































Результаты поиска

Содержание F34

Отзывы:

Axis F34, Руководство пользователя, Страница: 9 / 64

Результаты поиска

Содержание F34

Отзывы: