Axis F34 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 64

Axis F34 Скачать руководство пользователя страница 29

AXIS F34 Main Unit

Applications

Applications

AXIS Camera Application Platform (ACAP) is an open platform that enables third parties to develop analytics and other applications
for Axis products. For information about available applications, downloads, trials and licenses, go to

www.axis.com/applications

Note

• Several applications can run at the same time but some applications might not be compatible with each other. Certain

combinations of applications might require too much processing power or memory resources when run in parallel. Verify
that the applications work together before deployment.

Application Licenses

Some applications need a license to run. Licenses can be installed in two ways:

•

Automatic installation — requires access to the Internet

•

Manual installation — obtain the license key from the application vendor and upload the key to the Axis product

To request a license, the Axis product serial number (S/N) is required. The serial number can be found on the product label and under

System Options > Support > System Overview

.

Upload Application

To upload and start an application:

1. Go to

Setup > Applications

.

2. Under

Upload Application

, click

Browse

. Locate the application file and click

Upload Package

.

3. Install the license (if applicable). For instructions, see the documentation provided by the application vendor.

4. Start the application. Go to page

Applications

, select the application in the list of installed applications and click

Start

.

5. Configure the application. For instructions, see the documentation provided by the application vendor.

Note

• Applications can be uploaded by product administrators.

• Applications and licenses can be installed on multiple products at the same time using AXIS Camera Management, version

3.10 and later.

To generate a log file for the application, go to

Applications

. Select the application and click

Log

.

Application Considerations

If an application is upgraded, application settings, including the license, will be removed. The license must be reinstalled and
the application reconfigured.

If the Axis product’s firmware is upgraded, uploaded applications and their settings will remain unchanged, although this is not
guaranteed by Axis Communications. Note that the application must be supported by the new firmware. For information about
firmware upgrades, see

Upgrade the Firmware

If the Axis product is restarted, running applications will restart automatically.

If the Axis product is restored, uploaded applications remain unchanged but must be restarted. To start the application, go to

Setup > Applications

. Select the application in the list of installed applications and click

Start

. For information about restoring

the Axis product, see

29

«
...
27
28
29
30
31
...
»

Содержание F34

































































Отзывы:

Нет отзывов