AWB OD200-IDU Скачать руководство пользователя страница 34

Страница: 34 / 114

System Settings

4-2

System Status

The system status page displays connectivity status information for the unit’s
WiMAX (WAN) and LAN interfaces, firmware and hardware version numbers, and
the number of clients connected to your network.

Figure 4-2 System Status – Internet

INTERNET

– Displays WAN (WiMAX) connection status:

•

WAN IP

– Displays the IP address assigned by the service provider.

•

Subnet Mask

– Displays the WAN subnet mask assigned by the service provider.

•

Gateway

– Displays the WAN gateway address assigned by the service provider.

•

Primary DNS

– Displays the WAN primary Domain Name System server address.

•

Secondary DNS

– Displays the WAN secondary Domain Name System server

address.

•

Connection Type

– Displays the connection type for the WAN. Either FIXED for a

static IP setting, or DHCPC for dynamic IP assignment.

Figure 4-3 System Status – Gateway

GATEWAY

– Display system IP settings, as well as DHCP, NAT and firewall status:

•

IP Address

– Displays the unit’s IP address.

•

Subnet Mask

– Displays the subnet mask.

Содержание OD200-IDU



















































































































Результаты поиска

Содержание OD200-IDU

Отзывы:

Похожие инструкции для OD200-IDU

Бренды по названию

Популярные бренды

AWB OD200-IDU, Руководство оператора

Результаты поиска

Содержание OD200-IDU

Отзывы:

Похожие инструкции для OD200-IDU

Бренды по названию

Популярные бренды