AWB OD200-IDU Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 114

background image

3-1

Chapter 3: Initial Configuration

The OD200 can be configured through its web management interface. The web
interface provides a simple Basic Setup or Advanced Setup options.

Accessing the Web Management Interface

The OD200 has a default IP address of 192.168.1.1 and a subnet mask of
255.255.255.0. If your PC is set to have an IP address assigned by DHCP (Dynamic
Host Configuration Protocol), you can connect immediately to the web management
interface. Otherwise, you must first check if your PC’s IP address is set on the same
subnet as the OD200 (that is, the PC’s IP address starts 192.168.1.x).

In the web browser’s address bar, type the default IP address: http://192.168.1.1.

The web browser displays the OD200’s login page.

Figure 3-1 Login Page

Logging In

– Type the default User Name “admin” and Password “admin,” then click

Login. The home page displays.

«
...
25
26
27
28
29
...
»

Содержание OD200-IDU



















































































































Отзывы:

Нет отзывов

Похожие инструкции для OD200-IDU

Бренд: Genexis Страницы: 5

Бренд: Ubee Страницы: 119

Бренд: ZyXEL Communications Страницы: 2

Бренд: HID Страницы: 38

Бренд: Dinstar Страницы: 100

Бренд: ADI Страницы: 56

Бренд: Fife Страницы: 48

G.SHDSL.bis 4-port Security Gateway P-793H

Бренд: ZyXEL Communications Страницы: 444

Бренд: ADTRAN Страницы: 2

Бренд: ADTRAN Страницы: 30

Бренд: Hitachi Страницы: 18

Бренд: Hitachi Страницы: 56

Бренд: Hitachi Страницы: 50

Бренд: Siemens Страницы: 3

Бренд: Siemens Страницы: 12

6ES7647-0BA00-0YA2

Бренд: Siemens Страницы: 71

Бренд: Siemens Страницы: 138

Advance Network Gateway

Бренд: Siemens Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды