AVYCON AVK-TL91E4-1T Скачать руководство пользователя страница 78

Страница: 78 / 105

Device Management

DVR User Manual

Device Management

11.1 Network Configuration

11.1.1 TCP/IP Configuration

Click Start



Settings



Network



TCP/IP to go to the following interface. Check

“

Obtain an

IPv4 address automatically

”

“

Obtain an IPv6 address automatically

”

and

“

Obtain DNS

automatically

”

to get the network addresses automatically, or manually input the network

addresses. You can modify the MTU value according to the network condition (MTU,
Maximum Transmission Unit, can be modified according to network condition for higher
network transmission efficiency). Click

“

Apply

”

to save the settings.

11.1.2 Port Configuration

Click Start



Settings



Network



Port to go to the interface as shown below. Input the HTTP

port, server port and RTSP port of the DVR, enable

“

Watch video via anonymous login (not

need user name and password)

”

as required and then click

“

Apply

”

button to save the settings.

Содержание AVK-TL91E4-1T










































































































Результаты поиска

Содержание AVK-TL91E4-1T

Отзывы:

Похожие инструкции для AVK-TL91E4-1T

Бренды по названию

Популярные бренды

AVYCON AVK-TL91E4-1T, Руководство пользователя

Результаты поиска

Содержание AVK-TL91E4-1T

Отзывы:

Похожие инструкции для AVK-TL91E4-1T

Бренды по названию

Популярные бренды