manualshive.com logo in svg

Avnet PicoZed 7010, Руководство пользователя по оборудованию

Поделиться
Скачать
Avnet PicoZed 7010 Скачать руководство пользователя страница 8

 

 

3-Feb-2015 

7 

 

Table 4 

– USB 2.0 JX3 Pin Assignments 

Signal Name 

JX3 Pin 

USB_OTG_N 

69 

USB_OTG_P 

67 

USB_ID 

63 

USB_OTG_CPEN 

70 

 
 
If using the Avnet PicoZed FMC Carrier Card as the mating carrier card, a Micro-AB connector 
provided by FCI is used. The FCI part number is 10104111-0001LF.  
 
The usb0 peripheral is used on the PS, connected through MIO[28-39] in MIO Bank 1/501.  The 
USB Reset signal is connected to MIO[7]. Signal PS_MIO7 is a 3.3V signal. It is AND-ed with the 
power-on reset (PG_MODULE) signal and then level shifted to 1.8V through a TI TXS0102 level 
translator before connecting to the USB3320 Pin 27 RESET. 
 
PicoZed 7010/7020 is configured such that either Host Mode (OTG) or Device Mode can be used 
depending on the circuitry of the carrier card. With a standard connection to a baseboard (no 
power supply used to provide USB power to the connector) the device will operate in Device 
Mode. Using the USB_OTG_CPEN signal on JX3 allows the user to control an external power 
source for USB VBUS on the carrier card. Other considerations need to be made to 
accommodate Host Mode. Refer to the Avnet PicoZed FMC Carrier Card design for an example 
design for configuring the carrier card for either Host Mode or Device Mode.  
 
 

Table 5 

– USB 2.0 Pin Assignment and Definitions 

Signal Name 

Description 

Zynq Bank 

MIO 

SMSC 

3320 Pin 

Data[7:0] 

USB Data lines 

MIO Bank 1/501 

28:39 

Data[7:0] 

CLKOUT 

USB Clock 

MIO Bank 1/501 

1 

DIR 

ULPI DIR output signal 

MIO Bank 1/501 

31 

STP 

ULPI STP input signal 

MIO Bank 1/501 

29 

NXT 

ULPI NXT output signal 

MIO Bank 1/501 

2 

REFSEL[2:0] 

USB Chip Select 

N/C 

N/C 

8,11,14 

DP 

DP pin of USB Connector 

18 

DM 

DM pin of USB Connector 

19 

ID 

Identification pin of the 

USB connector 

23 

RESET_B 

Reset 

MIO Bank 1/501 

7** 

27** 

 
** Connected through AND-gate with PG_MODULE through level translator (TI TXS0102DQE). 
 

2.4  10/100/1000 Ethernet PHY 

PicoZed 7010/7020 implements a 10/100/1000 Ethernet port for network connection using a 
Marvell 88E1512 PHY.  This part operates at 1.8V.  The PHY connects to MIO Bank 1/501 (1.8V) 
and interfaces to the Zynq-7000 AP SoC via RGMII.    
 
The RJ-45 interface signals are connected to the JX3 Micro Header. 
 
 A high-level block diagram the 10/100/1000 Ethernet interface is shown in the following figure. 

Содержание PicoZed 7010





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды