manualshive.com logo in svg

Avnet PicoZed 7010, Руководство пользователя по оборудованию

Поделиться
Скачать
Avnet PicoZed 7010 Скачать руководство пользователя страница 20

 

 

3-Feb-2015 

19 

The table below shows the various voltage rails names on the schematic, the associated voltage 
for each rail, where they are connected on the Zynq 7010/7020, and where the voltage originates 
from. 
 

Table 15 

– PicoZed 7010/7020 Voltage Rails 

Schematic 

Voltage Name 

Voltage Level 

Zynq Connection 

Voltage 

Origination 

1.0V 

1.0V 

VCCINT 

SOM 

VCCBRAM 

VCCPINT 

VCCO_DDR3 

1.35V 

VCCO_DDR_502 (Bank 502) 

VTTREF 

0.675V 

PS_DDR_VREF0 (Bank 502) 
PS_DDR_VREF1 (Bank 502) 

1.8V 

1.8V 

VCCO_MIO1_501 (Bank 501) 

VCCAUX 

VCCPAUX 

3.3V 

3.3V 

VCCO_0 (Bank 0) 

VCC_MIO0_500 (Bank 500) 

VCCO_34 

1.8V/2.5V/3.3V 

VCCO_34 (Bank 34) 

JX1 

VCCO_35 

1.8V/2.5V/3.3V 

VCCO_35 (Bank 35) 

JX2 

VCCO_13 

1.8V/2.5V/3.3V 

VCCO_13 (Bank 13) 

JX2/JX3 

2.10.2  Voltage Regulators 

The following power solution provides the power rails of the PicoZed 7010/7020.  Sequencing of 
the supplies is implemented by cascading the POWER GOOD outputs of each supply to the 
ENABLE input for the next supply in the sequence.  3.3V is the last supply to come up, therefore 
the POWER GOOD for the 3.3V supply is used to drive the PG_MODULE net and is used as the 
power-on reset control for Zynq (U11.pin C7), Ethernet PHY (U4.pin 16), and USB-Host PHY 
(U5.pin 27). 
 
This net is also connected to the Micro Headers so power supplies on the end user carrier card 
can also control this signal. 
 

 

Figure 6 

– Regulation Circuitry (VCCIO_EN is PG_1V8) 

 
This circuit sequences power-up of PicoZed 7010/7020.  1.0V comes up first, then 1.8V, then 
VCCO_DDR3 and then 3.3V.  PG_MODULE is connected to PS_POR_B on Zynq, thus when the 
power supplies are valid, PS_POR_B is released. 
 
When the PicoZed 7010/7020 is mated to an end user carrier card, the POWER GOOD outputs 

Содержание PicoZed 7010





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды