AVM FRITZ! X USB Скачать руководство пользователя

Страница: 13 / 80

Connectors

FRITZ!X USB – 1 Introduction

Connectors

FRITZ!X USB uses the following connectors:

The ISDN cable supplied with FRITZ!X USB has an RJ45 plug
at each end. The power cord also has a RJ45 plug at one end.

Analog terminal devices are connected to FRITZ!X USB by
means of RJ12 plugs or the cable clips.

If your analog terminal device ist equipped with a plug type
other then RJ12, it can be connected to FRITZ!X USB by
means of an appropiate adapter, generally available in most
good electrical retail outlets.

The computer cable has a Series-A USB plug on one end and
a Series-B USB plug on the other.

RJ45 plug

RJ12 plug

USB connector
Series A

USB connector
Series B

F!XUSB-e.book Seite 13 Mittwoch, 8. November 2006 2:23 14

Содержание FRITZ! X USB

















































































Результаты поиска

Содержание FRITZ! X USB

Отзывы:

Похожие инструкции для FRITZ! X USB

Бренды по названию

Популярные бренды

AVM FRITZ! X USB, Руководство по установке

Результаты поиска

Содержание FRITZ! X USB

Отзывы:

Похожие инструкции для FRITZ! X USB

Бренды по названию

Популярные бренды