AvL Technologies AAQ IntelliTrack Module Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 27

AvL Technologies AAQ IntelliTrack Module Скачать руководство пользователя страница 26

IntelliTrack Module

Operations Guide

AvL Technologies

| Proprietary – Content is Subject to Change without Notice

pg. 25

The

IntelliTrack model

was not built
successfully

The

IntelliTrack Model

Charge %

sensor output is

“

100.00

” and the

IntelliTrack

Model Active

sensor output

is “

0

”. The system continues

to perform step track cycles.

Check that the system is pointed at the
intended target.

Check that the system Latitude, Longitude,
Heading, Time, and Date are correct.

The IntelliTrack module will continue to
gather step track data until it can build a
successful model. Check the

IntelliTrack

Model Active

sensor output again after

several hours.

System moves off
target while tracking
after it has built a
complete IntelliTrack
model

The

IntelliTrack State

sensor

output shows “

Maximum

Number Of Allowable
StepTrack Failures
Exceeded

” and the

Current

Signal Level

is below

expected levels.

Check that the current signal source is
configured correctly for the target
(attenuation, frequency, etc.).

Check that the desired signal device, feed,
and all cables are connected and
operational.

Check that the

IntelliTrack Reflector Size

is

configured correctly.

Check that all IntelliTrack StepTrack signal
configuration items are correct for the
current signal device.

Check that the system Latitude, Longitude,
Heading, Time, and Date are correct.

Erase the target IntelliTrack tracking data
using the

IntelliTrack Model Clear

target

configuration and restart tracking.

The system stops
tracking, but remains in
Track mode

The system stops moving.
The Track command in the
main window remains
illuminated.

Check the

IntelliTrack State

sensor output

for error messages. If error messages
appear, follow the recommended
troubleshooting procedure for that error.

Stop the Track command and attempt
other antenna movements. Check for
mechanical failures.

«
...
24
25
26
27
»

Содержание AAQ IntelliTrack Module




























Отзывы:

Нет отзывов