AvL Technologies AAQ IntelliTrack Module Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 27

AvL Technologies AAQ IntelliTrack Module Скачать руководство пользователя страница 11

IntelliTrack Module

Operations Guide

AvL Technologies

| Proprietary – Content is Subject to Change without Notice

pg. 10

Reference Satellite

Mode

4

Choice

Yes, No

Flag indicating that reference profiles

should be used if a heading is needed.

Run Track After

Acquire

4

Choice

Yes, No

Flag indicating that the Tracking Module

should run after a successful acquire

Run Track After Peak

4

Choice

Yes, No

Flag indicating that the Track Command

should run after a successful peak

command.

Run Track on Startup

4

Choice

Yes, No

Flag indicating whether the track command

should be run on start up

Skip Acquire Sat State

4

Choice

Yes, No

Flag indicating whether the acquire state

should be performed before entering track

mode.

Note – This must be set to “Yes” to use

IntelliTrack

Tracking Method

4

Choice

None, Intellitrack

Module, other

installed tracking

modules

Track Method to use after an Acquisition

has completed. Set to IntelliTrack Module.

IntelliTrack Model Clear

– Whether or not to clear all IntelliTrack tracking memory for the

current target profile when not tracking. This will clear the IntelliTrack model any time the
module enters or exits tracking.

IntelliTrack Signal Gradient Threshold

– This

parameter controls the maximum signal change

that will not cause a peaking decision error during step peaking. If this value is exceeded by the
Current Signal Gradient, then the peaking delay time will be reset. Setting this parameter to 0
will disable its functionality.

IntelliTrack Noise Noise Threshold

– This

parameter controls the maximum signal (noise)

change that will cause a peaking decision error during step peaking. If this value is exceeded by
the Current Signal noise, then the peaking delay time will be reset. Setting this parameter to 0
will disable its functionality.

Reference Profile 1

– This is the target profile to be used for a SatTant. Using a reference profile

will produce a more accurate heading than using the compass systems incorporated into the
antenna.

Note – A Reference Profile must always be used with the IntelliTrack Module. Refer to

the main user manual for information regarding Reference Profile configuration.

Reference Profile 2

- This is the target profile to be used for a SatTant if acquisition on

Reference Profile 1 is unsuccessful.

Note – A Reference Profile must always be used with the

IntelliTrack Module. Refer to the main user manual for information regarding Reference Profile
configuration.

«
...
9
10
11
12
13
...
»

Содержание AAQ IntelliTrack Module




























Отзывы:

Нет отзывов