Avidyne Entegra EX5000 Скачать руководство пользователя страница 72

Страница: 72 / 114

EX5000 Release 8.2.2 Installation Manual

P/N 600-00073-001 Rev 02

- 72 -

Pressing

Cancel

from the Underway state causes the current calibration session to end without

saving any interim calibration values.

Note:

For the fuel calibration procedure for the 530-00170-000, 530-00180-000, 530-00195-000,

530-00195-001, 530-00195-010, 530-00201-000 and 053-00235-000 software, see the Piper
Process Specification document PPS60185.

Torque Calibration (Optional)

For some aircraft, the MFD provides an interface to the Torque Calibration feature. If this feature is
available, the

Torque Cal

button displays.

For information about using the Torque Calibration feature, see the factory procedures for the aircraft.

5.11.2 Engine Sensor Checkout

After restarting the MFD, view the Engine page to verify data communication. Operate the aircraft
engine to confirm correct operation of all sensors.

The Percent Power function will not operate correctly on some models until the Aircraft Setup has
been completed.

5.12 Aircraft Setup

The options on the Aircraft Setup Page depend on the aircraft model and selected options for that
aircraft. These options may include:

•

Auxiliary Data

•

XM and FIS-B Broadcast Weather Datalink

•

Long Range Tanks

•

Checklists

•

Dimming Bus

Note:

The available options depend on the aircraft model, additional purchased features and

installed software. Your aircraft will not have all options available.



To configure the Aircraft Setup Page:

From Maintenance Mode, select Aircraft Setup. The Aircraft Setup Page displays:

Figure 24: Aircraft Setup Page with XM Broadcast Datalink

Содержание Entegra EX5000



















































































































Результаты поиска

Содержание Entegra EX5000

Отзывы:

Похожие инструкции для Entegra EX5000

Бренды по названию

Популярные бренды

Avidyne Entegra EX5000, Руководство по установке

Результаты поиска

Содержание Entegra EX5000

Отзывы:

Похожие инструкции для Entegra EX5000

Бренды по названию

Популярные бренды