manualshive.com logo in svg

Avidyne Entegra EX5000, Руководство по установке

Поделиться
Скачать
Avidyne Entegra EX5000 Скачать руководство пользователя страница 57

EX5000 Release 8.2.2 Installation Manual                                                                         P/N 600-00073-001 Rev 02  

- 57 - 

Table 22: ART-2000 Sensor Configuration Options  

Option 

Value 

Notes 

Park Position 

Last position 

Set the park/startup position for the radar antenna tilt angle. 

Full up 

Centered 

Full down 

Beam Width 

  10” Antenna 

  12" Antenna 

 
10

° 

8.1

°

 

Defines the Width and Height of the radar sweep graphical depiction 
on the EX5000 radar display. 

Beam Height 

0.0

o

 – 19.5

o

 

Enable Gain Control 

Check/Clear 

Enables R/T variable gain control to be commanded from the 
EX5000. 

Enable VP 

Check/Clear 

When checked, enables Radar Vertical Profile mode. 

Enable Auto-Tilt Control 

Check/Clear 

When checked, enables Radar auto-tilt mode. 

Primary Indicator (1) 

Check/Clear 

When checked, enables EX5000 control of radar functions. 

Disable Stabilization 

Check/Clear 

Disables EX5000 display of the “Stab Off” annunciation 

Enable Automatic Standby 

Check/Clear 

When checked, enables the EX5000 to auto-command the radar to 
standby when ground is sensed to be below 20 kts. 

 

5.10.1  RADAR System Calibration 

Calibrating the Radar R/T unit requires access to the Radar Calibration Page on the Entegra or 
Envision EX5000 unit. This section explains how to access the calibration page and complete the 
radar calibration.  

Perform radar R/T calibration according to the procedures and specifications for the specific unit 
installed in the aircraft. 

Calibration can be performed after the Radar has been installed, setup and checked out per the radar 
manufacturer’s instructions. 

  To calibrate the system: 

1. 

 

From the Maintenance Mode Page, select 

Setup Radar

. 

2. 

 

From the Radar Setup page. access the Calibration Mode 

3. 

 

Perform the calibration according to the specifications in the R/T unit's Installation Manual. 

4. 

 

Press Enter to accept the new values. 

5. 

 

When you are done, press 

Save 

from the Radar Setup Page. Press 

Cancel

 to exit without saving 

changes.  

6. 

 

Changes do not take effect until the MFD has been restarted. From the Maintenance Mode Page, 
press 

Restart System

. 

 

 

Содержание Entegra EX5000



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды