Avidyne 700-00004 Series Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 132

Avidyne 700-00004 Series Скачать руководство пользователя страница 101

EX5000 Installation Manual

P/N 600-00073 Rev 24

- 91 -

4.

Turn on the master switch to power up the EX5000. The Dataloader Page displays.

Note:

If the regular start screen displays, the EX5000 did not detect the Portable USB Device. Check
the connection between the Portable USB Device and the EX5000, then restart the procedure.

5.

Press

Proceed

. Do not turn off the EX5000 or disconnect the cable during a data load.The data

load is complete when the regular startup Page displays.

6.

After the startup Page displays, turn off power to the EX5000, remove your Portable USB Device,
and then turn the EX5000 power back on.

7.

This step ensures that all data has been checked in self-test and the MFD is ready for use.

8.

Store the Portable USB Device in a safe place.

7.2.2 Loading CMax Chart Data

Once you have downloaded the CMax data from your PC to a Portable USB Device, as described in
the

Avidyne Data Update Guide

, you will need to upload the data to your EX5000.

➤

To load CMax Data to your EX5000:

1.

With the MFD power OFF:

■

If using a USB Flash Memory Drive, plug it into the data port on the front of the EX5000.

■

If using a Zip Drive Dataloader, connect one end of the cable to the Zip Drive and the other
end to the EX5000 data port Do not insert the Zip disk into the Zip Drive until after you turn on
the MFD (in step 2).

Note:

Ensure that the Dataloader is supported and not dangling by the cable. Letting the Dataloader
dangle can cause permanent damage to the data port. It can also cause an intermittent
connection, which will result in an unsuccessful data update.

2.

Turn on the MFD. If you are using a Zip Drive, insert the Zip disk into the Zip Drive when the initial
Avidyne logo screen displays.

3.

The Dataloader Page displays.

➥

If this is the first-ever update, you may see a warning that you are about to load older data than the
MFD already contains. This is because the preloaded demo charts expire in the year 2020, so the
warning message is normal.

Press

Proceed

to start the chart data load.

4.

The Dataloader Page shows the progress as it loads the data into the MFD. After loading the data,
the Dataloader performs an integrity check on the data and displays a successful data load
message if all data is valid.

5.

When the operation is complete, the EX5000 will continue to the normal startup Page.

6.

At this point, turn off power to the EX5000, remove your Portable USB Device, and then turn the
EX5000 power back on.

This step ensures that all data has been checked in self-test and the MFD is ready for use

7.

Confirm the valid dates of the Chart data as reported on the Startup Screen.

«
...
99
100
101
102
103
...
»

Содержание 700-00004 Series





































































































































Отзывы:

Нет отзывов