manualshive.com logo in svg

Avidyne 700-00004 Series, Руководство по установке, Страница: 100 / 132

Поделиться
Скачать
Avidyne 700-00004 Series Скачать руководство пользователя страница 100

 

EX5000 Installation Manual

 

 

P/N 600-00073 Rev 24

- 90 -

This section describes moving data from your Portable USB Device to the EX5000.  

Note:

When removing the rubber cap from the data port, pull the cap gently 

from the top

 until it 

pops out. Make sure the cap is all the way out before plugging anything into the USB port.

 

 

Do not tug on the tab at the bottom of the cap, this could separate the cap from the EX5000 
bezel.

7.2.1 Loading NavData (the Navigation Database)

Your new EX5000 will be loaded with an up-to-date navigation database. Updates to the EX5000 
NavData database are available from Jeppesen Sanderson, Inc. every 28 days and can be purchased 
either individually or on a subscription basis.

Once you have downloaded the Nav from your PC to a Portable USB Device, as described in the 

Avidyne Data Update Guide

, you will need to upload the data to your EX5000.

➤

To load NavData to your EX5000:

1.

Bring the Portable USB Device to the EX5000 at the aircraft.

2.

Turn power OFF to the EX5000.

3.

Connect the data source to the EX5000:

■

If using a USB Flash Memory Drive, plug it into the data port on the front of the EX5000.

■

If using a Zip Drive Dataloader, put the Zip disk into the Zip Drive. Connect one end of the 
cable to the Zip Drive and the other end to the EX5000 data port.

Note:

Ensure that the Dataloader is supported and not dangling by the cable. Letting the Dataloader 
dangle can cause permanent damage to the data port. It can also cause an intermittent 
connection, which will result in an unsuccessful data update

! 

If using a Zip Drive Dataloader:

• Allowing the portable Zip Drive to dangle by the cable can result in damage to your MFD, or 

the Drive, as well as a data load failure.

• Do not insert the Zip disk into the Zip Drive until the regular start screen displays on the 

MFD. The disk may be damaged if it is already in the Zip Drive when power is applied. 

• After loading the CMax data into your MFD, wait until the disk is ejected from the drive before 

unplugging the Drive, or powering off the MFD. Unplugging the Zip Drive with the disk still 
engaged may cause damage to the disk.

! 

If using a USB Flash Memory:

• USB Flash Memory is only available for software part numbers 530-00180-( ) and later 

releases.

• Avidyne strongly suggests that, to avoid confusion, you reserve a USB Flash Memory Drive 

solely for EX5000 database transfers.

• After uploading data, do not remove the USB Flash Memory Drive until you see and 

acknowledge the regular EX5000 Startup screen.

Содержание 700-00004 Series





































































































































Отзывы:

Нет отзывов