background image

R F I D   S E T U P   G U I D E   &   S U P P L Y   C H A R T  

This 

RFID Setup Guide & Supply Chart

 contains RFID setup information for Monarch® 9855™ RFID 

printers.  Additional RFID documents are available on the enclosed CD-ROM and on our Web site 
(

www.monarch.com

).   

Your Monarch

 9855

 printer has been engineered to program (encode) an RFID (Radio Frequency 

Identification) tag before the label’s format is printed.  RFID tags, also called "transponders," contain an 
embedded programmable microchip and an antenna.   

The Signal and Read/Write value settings are recommended starting points.  You may need to adjust 
them based on your results.  If the Read/Write value settings are too high or too low, you may not be able 
to read the tags or you may change the data that was programmed in to adjacent RFID tags.  Use extreme 
caution when increasing or decreasing the Signal Adjust and Read/Write value settings because the RFID 
tag may become non-functional.  Printing over the RFID tag (or inlay) causes printing irregularity.   

The RFID supplies are sensitive to static electricity and can be damaged by static electricity.  
Connect the printer to a grounded electrical outlet and then ground yourself by touching some 
metal, such as the printer’s metal base, before handling the supplies. 

 

Note:

  Information in this document supercedes information in previous versions.  Check our Web site for 

any updates. 

D e t e r m i n i n g   t h e   H a r d w a r e   V e r s i o n  

There are three different hardware versions of the 9855 RFID printer (93110826, 93110841, and 
00000003).  The Read/Write value settings differ depending on your hardware version.  Follow these 
instructions to print an RFID configuration label to determine your hardware version. 

1.

 

From the printer’s 

Main Menu

, select 

Setup

RFID

, then 

Print Configuration

2.

 

Press 

Enter/Pause 

to print the configuration label. The hardware version is listed on the label. 

3.

 

Based on the hardware version, use the tables on the following pages to configure your RFID printer. 
The Read/Write settings are divided in to columns for each of the hardware versions.  If you have 
hardware version 93110826 or 93110841, follow the directions below for Selecting a Protocol (not 
needed for hardware version 00000003). 

S e l e c t i n g   a   P r o t o c o l  

When you turn on the RFID printer, “Monarch Initializing” flashes briefly and then you see “Print Mode 
Ready.”  If an error occurs while the printer is initializing, the error message flashes briefly on the display 
and then you see “Print Mode Ready.”  The printer displays “Not available” when you try to select the 
RFID menus if the module is inoperative.  The printer accepts RFID and non-RFID batches once you see 
“Print Mode Ready.”   

To select a protocol 

1.

 

From the printer’s 

Main Menu

, select 

Setup

RFID

, then 

Protocol

2.

 

When you see the protocol you want, press 

Enter/Pause

.   

3.

 

After you select a protocol, you are prompted to enter the Read and Write value settings and the 
Signal Adjust.   

Use the tables on the following pages to configure your RFID printer, based on your RFID supplies, 
protocol, and hardware version.   

Monarch

 and 9855

 are trademarks of Avery Dennison Retail Information Services LLC.   

Avery Dennison

 is a trademark of Avery Dennison Corp.   

Alien, Alien Technology, and Squiggle are trademarks of Alien Technology Corporation.   
Impinj and MonzaRFID are trademarks of Impinj, Inc.   

TC9855RFIDSWC  Rev. BD  3/12  

2010 Avery Dennison Corp.  All rights reserved.

 

Содержание Monarch 9855

Страница 1: ...n Follow these instructions to print an RFID configuration label to determine your hardware version 1 From the printer s Main Menu select Setup RFID then Print Configuration 2 Press Enter Pause to print the configuration label The hardware version is listed on the label 3 Based on the hardware version use the tables on the following pages to configure your RFID printer The Read Write settings are ...

Страница 2: ...3110841 10 10 10 93110826 10 Avery Dennison AD 224 NXP G2XM Note Contains programmable user memory 4 0 x 1 375 00000003 10 10 93110841 4 4 4 93110826 Avery Dennison AD 226 4 0 x 1 375 00000003 4 4 93110841 4 4 4 93110826 4 Avery Dennison AD 230 Impinj Monza 3 3 0 x 1 5 00000003 4 4 93110841 1 5 93110826 Avery Dennison AD 231 Impinj Monza 4D 3 0 x 1 5 00000003 2 5 93110841 15 6 6 93110826 15 6 Aver...

Страница 3: ...110826 16 Avery Dennison AD 805 Impinj Monza 3 1 0 x 1 75 00000003 17 16 93110841 7 93110826 Avery Dennison AD 814 Impinj Monza 1 125 x 2 0 00000003 7 7 93110841 15 13 13 93110826 Avery Dennison AD 815 Impinij Monza 3 1 0 x 1 2 00000003 15 13 93110841 6 6 6 93110826 6 Avery Dennison AD 826 Impinj Monza 3 Note Use with 6 0 IPS max print speed 1 5 x 3 25 00000003 6 6 93110841 9 9 9 93110826 9 Avery ...

Страница 4: ...t The trailing edge is the edge of the label that exits the printer last regardless of how the format is designed on the label Non Print Zone Trailing Edge Leading Edge The non print zone varies for 1 Feed RFID Supplies 4 wide by 1 tall RFID Label Print Position Transponder Type 203DPI 300 DPI Supply Position Non Print Zone Alien Technology Higgs Squiggle 40 60 50 0 30 trailing edge Avery Dennison...

Отзывы: