Avaya programming and use Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 468

Avaya programming and use Скачать руководство пользователя страница 83

Initial System Programming

Configuring the T1 Module

3-9

6.

Dial the extension number of the telephone to be programmed.

The green lights next to buttons on which lines or pools are assigned show the current Line
Ringing settings. The remaining buttons can be programmed with telephone numbers,
extension numbers, or system features.

7.

At this point, program the features that must use Centralized Telephone Programming.

8.

To change the settings for another extension, press

c

; then dial the new extension

number.

9.

To exit programming mode, you can press

f00

, or lift the handset and place it back in

the cradle.

Configuring the T1 Module

3

To configure a T1 module, you must use the PARTNER ACS R6.0 PC Administration software.
You cannot program or view the administration of a T1 module via System Programming from
extensions 10 or 11. For instructions on how to install the PARTNER ACS R6.0 PC Administration
software on a PC, see the PARTNER

®

ACS R6.0 PC Administration Getting Started.

Configuring a T1 module consists of the following steps:

1.

Start PARTNER ACS R6.0 PC Administration.

2.

Connect to the PARTNER system.

3.

Back up and retrieve the translations from the PARTNER system.

4.

Save this file as a new file.

5.

Verify that the PARTNER system has a T1 module.

6.

Configure the settings for the T1 module.

7.

Administer the settings for each line (channel) you will use on the T1 module.

8.

If you will be using the Direct Inward Dialing (DID) service from the T1 service provider,
configure the DID Mapping Table. (You will “map” extensions, hunt groups or calling groups to
DID numbers.)

9.

Program the other features (such as extension features and restrictions) you want. (See the
procedures in “Program PARTNER Features in a PC Administration File” in the online help.)

10. Save the file.

11. Program the settings in this file to the PARTNER system.

Refer to

“Initial Configuration of the T1 Module” on page 2-19

or “Program a T1 Module” in the

PARTNER ACS R6.0 PC Administration online help for detailed instructions on how to perform
these procedures.

After configuring the T1 module, you may perform the Set Administration procedures in this guide
to administer non-T1 settings. You can also administer non-T1 settings from the PARTNER ACS
R6.0 PC Administration software.

«
...
81
82
83
84
85
...
»

Содержание programming and use





















































































































































































































































































































































































































































































Отзывы:

Нет отзывов