Avaya programming and use Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 468

Avaya programming and use Скачать руководство пользователя страница 160

PARTNER

®

Advanced Communications System Installation, Programming, and Use

System Reset—Programming Saved (#728)

4-62

Programming

4

To program a System Password:

1.

Press

f00ss#403

at extension 10 or 11. A display

similar to the following appears:

Set

System

Password

Data

-

-

-

-

-

-

-

-

-

-

-

-

2.

Enter a four-digit password, or press

r

to delete the existing password.

3.

Select another procedure, or exit programming mode.

System Reset—Programming Saved (#728)

4

Use this feature to reset the system while retaining the currently programmed settings. Reset the
system only when advised to do so by technical support personnel.

Considerations

4

■

Resetting the system disconnects all active calls.

■

This procedure is skipped in the sequence of programming procedures when cycling. To use
this procedure, enter the code directly.

■

The system reset begins immediately and takes only a few seconds.

■

You cannot interrupt the reset process or use any telephones in the system during the reset
process.

■

Most of the system and telephone programming settings that were in effect before the power
failure or down period are retained; they do not revert to the default settings.

■

Automatic System Answer Button (#111), Direct Extension Dial Button (#113), Night
Service Button (#503), and Station Lock return to the status (on or off) that they were in
immediately prior to the system reset.

■

The VMS Cover button and Privacy button return to the status (on or off) determined by the
programmed setting of Automatic VMS Cover (#310) and Automatic Extension Privacy
(#304), respectively. For example, if Automatic Extension Privacy is Assigned and the
Privacy button is on when a system reset occurs, the Privacy button will be on again after the
system reset. However, if Automatic Extension Privacy is Not Assigned and the Privacy
button is on when a system reset occurs, the Privacy button will be off after the system reset.

■

A successful use of Restore Programming (#125) causes a System Reset—Programming
Saved to occur.

■

The information stored in the Save Number Redial (F04) and the Last Number Redial (F05)
buffers is lost when a System Reset—Programming Saved occurs.

■

You can use System Reset—Programming Saved to restore the configuration in the 1600
DSL module.

«
...
158
159
160
161
162
...
»

Содержание programming and use





















































































































































































































































































































































































































































































Отзывы:

Нет отзывов