Avaya programming and use Скачать руководство пользователя страница 155 | Manualshive

Страница: 155 / 468

Avaya programming and use Скачать руководство пользователя страница 155

Programming System Options

Remote Call Forwarding (#322)

4-57

Remote Call Forwarding (#322)

4

Use this feature to activate Remote Call Forwarding for an extension. When activated, you can
forward all intercom, transferred, and outside calls from your extension to an outside telephone
number via Remote Call Forwarding or Cell Phone Connect. See

“Remote Call Forwarding

(F11)” on page 8-59

“Cell Phone Connect (F11)” on page 8-27

for more information.

Considerations

4

■

Remote Call Forwarding must be enabled before you can forward calls via Cell Phone
Connect and Remote Call Forwarding.

■

For analog lines and T1 lines without DID, the extension must be the Line Coverage
Extension (#208) for that line.

■

You can forward outside, intercom, transferred, and voice-signaled calls.

■

You cannot forward group calls, calls to doorphone alert extensions, Voice Interrupt On Busy
calls, coverage calls, transfer-return calls, Wake Up Service calls, and Night Service calls.

■

Remote Call Forwarding does not apply to parked calls. See

“Call Park” on page 8-14

■

You cannot use Call Screening (F25) for calls that are forwarded.

■

The PARTNER system will forward only calls on lines that have reliable disconnect. For these
lines, Hold Disconnect Time (#203) must be set to a value other than 00 (No Detection).

■

The extension must have an available line to forward the call to an outside number.

■

The PARTNER system uses the extension’s Automatic Line Selection to determine which
line to use for the outgoing call.

Programming

4

To change the Remote Call Forwarding setting for an extension:

1.

Press

f00ss#322

at extension 10 or 11.

2.

Enter the number of the extension to be programmed.

3.

To assign or unassign Remote Call Forwarding, press

D

until the appropriate value

appears.

■

1 = Assigned

■

2 = Not Assigned (the factory setting)

4.

To program another extension, press

n

or

p

until the extension number appears

on the display. Then repeat step 3.

5.

Select another procedure, or exit programming mode.

«
...
153
154
155
156
157
...
»

Содержание programming and use





















































































































































































































































































































































































































































































Отзывы:

Нет отзывов