Avaya programming and use Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 468

Avaya programming and use Скачать руководство пользователя страница 106

PARTNER

®

Advanced Communications System Installation, Programming, and Use

Call Coverage Rings (#116 or #320)

4-8

4.

Press

e

to start the restore.

If the system detects an error before beginning the restore, the bottom line of the display
shows one of the following messages (See

Chapter 11, “Troubleshooting”

for more information

about these messages):

■

Insert

Card

or

Insert

Valid

Card

■

Bad

File

or

Bad

File-Try

Again

■

Incompat

Version

or

Incompatible

Versions

■

Empty

File

If the system does not detect an error, the restore begins. One of the following occurs:

■

When the restore has completed successfully, the bottom line of the display shows

Restore

Complete

for two seconds. Then the system resets itself, which means that all

calls in progress are disconnected. You are no longer in System Programming mode.

■

If the restore is not successful, the display shows

Restore

Failed

or

Restore

Failed-Try

Again

for two seconds. All calls in progress are disconnected and all of the

system and telephone programming settings revert to the factory settings. You are no
longer in System Programming mode. Try the restore again.

Call Coverage Rings (#116 or #320)

4

Use this feature to define the number of times intercom, transferred, and outside calls on lines
assigned ownership ring at an extension before they are sent to the covering extension. In
Release 2.0 of the system, when you program Call Coverage Rings (#116), it applies to all
system extensions programmed for Call Coverage. In systems of Release 3.0 or later, you can
program Call Coverage Rings (#320) on an individual extension basis.

Considerations

4

■

If an extension has Call Coverage and VMS Cover active, covered calls ring at the covering
extension for the specified number of Call Coverage Rings:

— If the covering extension does not answer, the call is routed to the voice mailbox of the

extension that activated Call Coverage after the specified number of VMS Cover Rings
(#117) or (#321).

— If the covering extension has Do Not Disturb active, the call is routed immediately to the

voice mailbox of the extension that activated Call Coverage.

«
...
104
105
106
107
108
...
»

Содержание programming and use





















































































































































































































































































































































































































































































Отзывы:

Нет отзывов