Avaya P332GT-ML Скачать руководство пользователя страница 31

Страница: 31 / 150

Avaya P332GT

-ML User’s Guide

Chapter 4

Installation

The P332GT-ML is ready to work after you complete the installation instructions
below.

Required Tools

Make sure you have the following tools at hand before undertaking the Installation
procedures:
•

Philips (cross-blade) screwdriver

Site Preparation

Avaya P330 can be mounted alone or in a stack in a standard 19-inch equipment
rack in a wiring closet or equipment room. Up to 10 units can be stacked in this way.
When deciding where to position the unit, ensure that:
•

It is accessible and cables can be connected easily and according to the
configuration rule.

•

Cabling is away from sources of electrical noise such as radio transmitters,
broadcast amplifiers, power lines and fluorescent lighting fixtures.

•

Water or moisture cannot enter the case of the unit.

•

There is a free flow of air around the unit and that the vents in the sides of the
case are not blocked.

Note:

Use Octaplane cables to interconnect with other switches.

•

The environmental conditions match the requirements listed below:

Table 4.1

Environmental

Prerequisites

Operating Temp.

-5 to 50°C (23 to 122°F)

Relative Humidity

5% to 95% non-condensing

Содержание P332GT-ML























































































































































Результаты поиска

Содержание P332GT-ML

Отзывы:

Похожие инструкции для P332GT-ML

Бренды по названию

Популярные бренды

Avaya P332GT-ML, Руководство по установке и настройке

Результаты поиска

Содержание P332GT-ML

Отзывы:

Похожие инструкции для P332GT-ML

Бренды по названию

Популярные бренды