Avaya P332GT-ML Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 150

background image

Chapter 12

Avaya P330 Layer 3 Features

104

Avaya P332GT

-ML User’s Guide

The DHCP/BOOTP server uses the relayed network information to decide from
which subnet the address should be allocated. Therefore, the DHCP/BOOTP server
must be configured to allocate addresses from the relayed networks configured on
the P330.
DHCP/BOOTP Relay in P330 is configurable per VLAN and allows you to specify
two DHCP/BOOTP servers. In this case, it duplicates each request, and sends it to
both servers. This provides redundancy and prevents the failure of a single server
from blocking hosts from loading.
You can enable or disable or DHCP/BOOTP Relay in P330.

BOOTP/DHCP CLI Commands

In order to...

Use the following command...

Enable or disable relaying of bootp
and dhcp requests to the BOOTP/
DHCP server

[no] ip bootp-dhcp relay (no -
restores default)

Add or remove a BOOTP/DHCP
server to handle BOOTP/DHCP
requests received by this interface

[no] ip bootp-dhcp server (no -
restores default)

Select the networks from which the
bootp/dhcp server shall allocate an
address

[no] ip bootp-dhcp network (no -
restores default)

«
...
116
117
118
119
120
...
»

Содержание P332GT-ML























































































































































Отзывы:

Нет отзывов

Похожие инструкции для P332GT-ML

Бренд: eao Страницы: 2

Бренд: eao Страницы: 2

Бренд: Dataprobe Страницы: 3

Бренд: Panasonic Страницы: 206

Бренд: 6TL Страницы: 25

Sierra Video 1208V3S

Бренд: Kramer Страницы: 2

Бренд: G-Lab Страницы: 12

StorageWorks SAN Switch Integrated/32

Бренд: Compaq Страницы: 104

Crocodile Tail Loop

Бренд: One Control Страницы: 9

Бренд: Aruba Networks Страницы: 40

Бренд: Scion-Tech Страницы: 9

EasyZAPP EZ CEFL

Бренд: DANLERS Страницы: 2

Бренд: Versa Technology Страницы: 12

Бренд: Jasco Страницы: 2

Бренд: Encore Страницы: 1

AMX DVX-2265-4K

Бренд: Harman Страницы: 2

Бренд: AVG Страницы: 41

Бренд: 3onedata Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды