Avaya J129 Скачать руководство пользователя страница 76

Страница: 76 / 133

getAllEndpointConfiguration

request is unsuccessful, the

getContactList

request is also

ignored. This request contains the following fields:

• VolumeSettings

• LinePreferenceInfo

• ListOfOneTouchDialData

• ListOfButtonAssignments

• SoftMenuKeyList

• DialPlanData

• ListOfSpeedDialData

• ListOfMaintenanceData

• ListOfTimers

• VMONInfo

• ListOfRingerOnOffData

• ListOfNumberFormatRules: Applicable only when registered to Avaya Aura

Session Manager.

• ListOfIdentities: Applicable only when registered to Avaya Aura

Session Manager.

MWExt: Applicable only when registered to Avaya Aura

Session Manager.

• VMNumber: Applicable only when registered to Avaya Aura

Session Manager.

Provisioning survivability for SIP phones

About this task

Use this procedure to provision survivability.

In IP Office environment, survivability is provisioned in the autogenerated Settings file.

Procedure

1. Set the applicable failover configuration parameters in the

46xxsettings.txt

file.

2. Provision the gateway per the Application Notes, available on the

https://support.avaya.com/

website.

3. Load the latest SIP Release software and associated files on the file server.

4. Reboot all registered phones from SIP Enablement Services or Avaya Aura

Session

Manager.

5. Power up other phones.

System failover

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Содержание J129






































































































































Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды

Avaya J129, Установка и администрирование

Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды