Avaya J129 Скачать руководство пользователя страница 72

Страница: 72 / 133

Chapter 9: System failover

Supported SIP environments

Avaya J129 IP Phone work on the following environments:

• Avaya Aura

Session Manager with Avaya Aura

Communication Manager

• IP Office

• Failover and survivable interoperability with the following SIP gateways:

- Session Manager for survivable remote gateway

- Avaya Secure Router 2330 and 4134

- Audiocodes MP-series analog and BRI gateways

- Avaya Aura

Media Server 7.7.0.334.

- IP Office

For information about configuring the phone features, see the following documents:

•

Avaya Aura

Communication Manager Feature Description and Implementation

•

Administering Avaya Aura

Communication Manager

•

Avaya IP Office

™

Platform SIP Telephone Installation Notes

Failover and survivability overview

The phone detects a network or server failure in approximately 90 seconds. After a failure is

detected, the phone selects an active controller in approximately five seconds. During network or

server failures, multiple controllers or servers are supported for the following operations:

• Making a call including emergency calls
• Receiving a call
• Call transfer
• Call forward
• Mid call features: Call hold and mute
• Audio Conference: Local three-way audio conference

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Содержание J129






































































































































Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды

Avaya J129, Установка и администрирование

Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды