Avaya J129 Скачать руководство пользователя страница 48

Страница: 48 / 133

Feature

Survivable operation with third-
party proxy

Normal operation with
Communication Manager and
Session Manager

administered, users can gain to the
voice mailbox.

Mute alert

Yes

Presence

—

Yes

Send All Calls Enable/Disable

—

Yes

SSH support

Yes

Third Party Call Forward

—

Yes

Third Party Call Forward Busy
Don’t Answer

—

Yes

Attended Transfer

Yes

Transfer upon hang-up

—

Yes

Administering emergency numbers

When the phone is locked or when the user is not logged in, it is possible to configure phones to

make emergency calls. Depending upon the configuration parameters and whether or not the SIP

proxy supports emergency dialing, it is possible to enable this functionality in the overall SIP

solution.

Avaya J129 IP Phone displays an

Emerg

softkey when the phone is not registered or when the

phone is locked. When the

Emerg

softkey is pressed, the user can call a primary emergency

number. There are three parameters associated with this emergency dialing:

• PHNEMERGNUM: Specifies the primary emergency number that a user calls when the

Emerg

sofkey is pressed. Also, by specifying the PHNEMERGNUM parameter a user can dial the

emergency number manually.

• ENABLE_SHOW_EMERG_SK: Specifies whether the phone displays Emerg softkey when the

phone is registered and whether the phone displays a confirmation dialogue box when

Emerg

softkey is pressed.

• ENABLE_SHOW_EMERG_SK_UNREG: Specifies whether the phone displays Emerg softkey

when the phone is not registered and whether the phone displays a confirmation dialogue box

when

Emerg

softkey is pressed.

In Avaya J129 IP Phone you can set up to 100 additional emergency numbers to dial. You can

define the numbers using the following parameter:

• PHNMOREEMERGNUMS: Specifies the additional emergency phone numbers.

In the Avaya Aura

environment, you can configure the parameters in System Manager. You must

select the

Allow Unauthenticated Emergency Calls

field in System Manager so that users can

dial the emergency number when the phone is not registered. However, when a user logs into an

Avaya Aura

environment, only the emergency numbers configured in SMGR will be used by the

Avaya Aura configuration for phones

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Содержание J129






































































































































Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды

Avaya J129, Установка и администрирование

Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды